Results 1 to 7 of 7
  1. #1
    Junior Member
    Join Date
    Sep 2008
    Posts
    12
    Thanked: 0

    Default Strange Goop / Light Rust

    Howdy all,

    I purchased my first straight razor, a Dovo Black Star, from the BST section over here. It arrived wonderfully packed yesterday, but when I inspected the blade I noticed it a strange goo coating the lower part of the blade. It felt like the residue that is left behind when you remove a price tag / bar code from plastic or glass. I contacted the seller who told me he had only used the razor three times, and shipped it with mineral oil on the blade.

    I tried to run the blade under hot water to see if that would work, but as I wiped off the water I discovered it had not. (I was wiping the razor and spine, and doing a super light towel strop to clean the edge.) I then let it sit for 10 or so minutes as I poked around online looking for a good cleaning method. I wound up deciding to have a go with regular dish soap and very hot tap water. That took it right off, but there is still a little bit of junk left very close to the edge, as I was neurotic about cleaning that close to the edge with the sponge. I then removed the water in the same way.

    Low and behold, I have now noticed slight rust spots on the blade as pictured below. Is it possible that these came from my use? I have trouble believing that is possible. I've used carbon steel knives my entire life and have *never* seen one rust that fast.

    So questions:
    1) Any suggestions for cleaning off that last bit of junk?
    2) Is the rust my fault?
    3) Do you think I should contact the seller about a possible partial refund?

    Thanks!





  2. #2
    what Dad calls me nun2sharp's Avatar
    Join Date
    Feb 2008
    Location
    Kansas city area USA
    Posts
    9,172
    Thanked: 1677

    Default

    Soaking in water was probably not the best thing, but the rust on the edge should come off with a good stropping or a light honing. If its actually just a little rust. BTW the honed edge is more prone to rust than the finished steel since it is raw and not mirrored. Hope this helps.
    Last edited by nun2sharp; 09-20-2008 at 03:29 PM.
    It is easier to fool people than to convince them they have been fooled. Twain

  3. #3
    Junior Member
    Join Date
    Sep 2008
    Posts
    12
    Thanked: 0

    Default

    I should probably clarify that I meant I was running it under water, then I dried it off. It was run under water and dried off twice.

    EDIT: Also, how would the rust come off with stropping? It's on the blade so it never touching the strop. (Or so I thought.)
    Last edited by Shibsky; 09-20-2008 at 03:29 PM.

  4. #4
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    You might try just some WD40 on a piece of tissue paper, that might solve both of the problem really easily...

  5. #5
    The Hurdy Gurdy Man thebigspendur's Avatar
    Join Date
    May 2005
    Location
    New Mexico
    Posts
    32,736
    Thanked: 5016
    Blog Entries
    4

    Default

    If its just some light surface rust a pencil eraser should do the trick.
    No matter how many men you kill you can't kill your successor-Emperor Nero

  6. #6
    Junior Member
    Join Date
    Aug 2008
    Posts
    23
    Thanked: 1

    Default

    It is hard to tell from the pictures, but that gunk looks a lot like the soap gunk that builds up on my razor and brush handle-which is also metal (I have very hard water where I live).

    The way I get rid of it is to use warm water with dish soap. Use a container that is deep enough to completely submerge your blade. Add the dish soap after the water and swirl it around otherwise you will get a large head of soap that is a nuisance to work around.

    Submerge the blade in the soapy water and using a Q-tip, I rub the gunk off. You don't need much pressure and dunk the blade as needed to help break up the stuff.

    Thoroughly rinse when done.

    This should go without saying, be sure to completely dry the blade, pivot area and the inside of the scales when done.

    Hope this helps.

    ~Robert

  7. #7
    Senior Member Lt.Arclight's Avatar
    Join Date
    Aug 2008
    Location
    New Jerseystan
    Posts
    559
    Thanked: 111

    Default

    I've also found a slurry of Bon-Ami-mixed between my fingers and rubbed on the blade under hot water will remove the "gunk". I had a similar problem with a new Dovo"silver steel" Prima.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •