I was wondering what the difference is in full half quarter etc.
i just picked up a razor off ebay that seems very thin and loud when i touch it.
im assuming its a full ground, but possible could be singing?
Thanks
Printable View
I was wondering what the difference is in full half quarter etc.
i just picked up a razor off ebay that seems very thin and loud when i touch it.
im assuming its a full ground, but possible could be singing?
Thanks
Not to derail you, Ben, but I actually prefer this image to answer that question:
http://straightrazorpalace.com/srpwi.../GrindForm.GIF
Not to derail you, but that image is contained in Ben's link.
.... Wow. How did I miss that >.<
Mea culpa, Ben, Robin.
ok but whats the difference in shaves, is one easier or smoother to shave with, do you have to use more pressure with one over the other?
There isn't much difference in shave if they are all at the same sharpness... However, more hollow blades will "flex" more... It's just a difference in technique.
Also, for heavier beards, heavier blades cut better due to the weight... Like a snow plough versus a shovel
There is no universally valid answer to that question. More hollow grinds typically offer more flex, which some people like, and others hate. Less hollow grinds also provide less feedback, again a matter of personal preference. Add various widths, and you will understand why this question cannot be answered.
Pressure is never used.
If sharpness is equal I do believe that the heavier grinds work better on heavier beards but I believe it has more to do with the skill and technique of the user. A stiff, heavy blade seems to be more forgiving of bad technique and lack of skill. A lighter, more flexible hollow grind seems to demand greater skill and proper technique.
I'm experiencing the opposite. The more hollow ground razor is cutting with less "momentum" needed to not get stuck in the dense, coarse chin & moustache hairs, and trimming the hairs closer per pass than the less hollow ground razor. I also find that I have a tendancy to use more pressure against the face with the less hollow razor, since otherwise it doesn't shave as close as the more hollow razor.
I never understand that term feedback.
Since a hollow blade has some flex and is lighter if your technique is not spot on it makes the blade hang up easier in the hair where a heavier grind and razor will plow through just about anything even with really bad technique. When I have used the heavier grinds for a time and then switch to a hollow grind I find I have to "relearn" how to use the hollow grind ( I am talking full hollows here)But when I switch from a hollow to a wedge I find no need to "relearn"
thanks for the clarification, but I guess you wouldn't use a heavy blade on a light weight stubble:)
The real problem with the usual heavy beard, heavy blade discussion is that we all have different beards. I have extremely course hair in my beard. When I use a full hollow during the first, and ATG pass there is a real tendency for the blade to flex to a point where it will get some skin. When I am shaving I tend to ride the edge which means that the cutting part of the blade is just above the skin. I have use some thin full hollows that just will not give me an irritation free shave. I like doing 4 pass shaves with a touch-up added and the alum block after a full hollow shave is murder.
I have often wondered if a professional barber could weigh in and give his point of view. His point may be slanted a little because a prep with 3 hot towels and 45 minutes but, none the less I would bet there would be some really good insight.
Take Care,
Richard
I have tried shaving with a 5/8 Dovo special, 6/8 Dovo special, and 5/8 Dovo silversteel (Ebony). The particular silversteel I used is a bit less hollow ground than the 2 particular specials and feels a little stiffer. I get the most feedback from the 5/8 special. ie: I can hear the difference in how well my angle is cutting hairs the best. They all give PLENTY of feedback though (even for my newbie ears).