Page 1 of 2 12 LastLast
Results 1 to 10 of 16
Like Tree52Likes

Thread: New Brush that is kind of disappointing

  1. #1
    MrZ
    MrZ is offline
    Senior Member
    Join Date
    Sep 2017
    Location
    Upstate New York
    Posts
    640
    Thanked: 104

    Default New Brush that is kind of disappointing

    I picked up a Vulfix 44 best badger brush at an auction. The price was less than ten dollars, but the brush is terrible soft. It really has very little backbone. It is big and pretty, but it doesnt want to whip up a lather. I will have to try it with shaving creams instead of pucks or my go to Proraso. (As an aside, I did get two things of proraso pre shave and one proraso after shave for Christmas!)
    rolodave and outback like this.

  2. #2
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    11,924
    Thanked: 4300

    Default

    I've got a couple brushes,like u describe. I found they work very nicely, with creams, and glycerin, soaps.

    Won't do squat, with tallow pucks.
    Mike

  3. #3
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,250
    Thanked: 3221

    Default

    You could try loading soap with a fairly dry bush to start off with add a little water and load some more. Repeat as necessary and then lather up. You could also try blooming the puck first.



    Bob
    Life is a terminal illness in the end

  4. #4
    Senior Member blabbermouth tintin's Avatar
    Join Date
    Jun 2013
    Location
    archbold ohio
    Posts
    2,363
    Thanked: 545

    Default

    since you didn't pay much for it , it might be worth steaming the knot out and drilling the hole deeper to give it more backbone. I've done it with a brush that i won and it worked well. Might be something to consider, JMHO
    Jimbo, rolodave, BobH and 4 others like this.

  5. #5
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    All good ideas and comments. One more to think about. With your fingertips reach all the way past the handle and use your fingertips on the base of the knot. This will also give it more backbone.
    Or raid the wife's hair ties and put one on the knot right where the hair is at the handle. Try two. But remember to remove it when drying.
    It's just Sharpening, right?
    Jerry...

  6. #6
    Senior Member blabbermouth
    Join Date
    Feb 2018
    Location
    Niagara, Ontario, Canada
    Posts
    2,767
    Thanked: 550

    Default

    I have one very soft badger brush that works great for face lathering with a cream and not so great building a lather from a puck in a bowl.

    My hypothesis is that when face lathering, the excess water in the bristles just rolls down my face, but it just pools in the bowl making the lather too thin.
    rolodave likes this.
    David
    “Shared sorrow is lessened, shared joy is increased”
    ― Spider Robinson, Callahan's Crosstime Saloon

  7. #7
    STF
    STF is offline
    Senior Member blabbermouth STF's Avatar
    Join Date
    Oct 2019
    Location
    Kingsville On, Canada
    Posts
    2,435
    Thanked: 207

    Default

    Quote Originally Posted by tintin View Post
    since you didn't pay much for it , it might be worth steaming the knot out and drilling the hole deeper to give it more backbone. I've done it with a brush that i won and it worked well. Might be something to consider, JMHO
    Interesting, I have a quite cheap Q Shave badger brush but i don't like it because although it looks nice it has no backbone and just kind of splays out and goes soft and annoying when I use it.

    How much deeper should I make the hole or how should I decide because i don't want to overdo it.

    This is quite exciting, I get to use my new forstner bits on something real instead of finding things in the house that needed a hole (I got in a lot of trouble for that).
    Johntoad57 and MrZ like this.
    - - Steve

    You never realize what you have until it's gone -- Toilet paper is a good example

  8. #8
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default

    Before you yank out the knot and drill, try soaking in vinegar and washing with shampoo.

    Then measure the knot at the base with a pair of calipers. You can buy an inexpensive pair of calipers for under $5 or use a compass and measure the distance between the points. If you have trouble measuring a soft knot, run a wrap of masking tape around the base of the knot.

    Buy a thick O-ring just a bit smaller than the knot size. You can experiment with the placement of the ring or with different thickness of rings. Use it with the O-ring or if you want to drill, you will know how deep it needs to be.

    Washing a brush with vinegar will do wonders for any brush, I soak and wash my brushes a couple times a year. Some soaps will clog a brush faster than others.
    Jimbo, 32t, rolodave and 2 others like this.

  9. The Following User Says Thank You to Euclid440 For This Useful Post:

    STF (01-05-2021)

  10. #9
    32t
    32t is offline
    Senior Member blabbermouth 32t's Avatar
    Join Date
    Oct 2010
    Location
    50 miles west of randydance
    Posts
    9,573
    Thanked: 1352

    Default

    If you use an o ring or hair tie as a general rule only move from the handle up.

    If you move it to high start over from the handle up.

    Messes the bristles up.
    rolodave likes this.

  11. #10
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    The o-ring or hair tie will let you know how much more deep it needs to be.but some knots are just too soft and floppy. This means that if you set it in more it might not lather worth a damn. This is why I think you find the lump shape of epoxy inside some low cost knots. The limp holds the hairs up and gives it a little stiffness. A low cost, floppy brush is just not worth any efort in fixing unless you really like it. Otherwise, just buy better quality next time.

    I bet I have 10 to 12 brushes I dont use because they dont make me happy for one reason or another.
    Steve56, MrZ and STF like this.
    It's just Sharpening, right?
    Jerry...

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •