Page 1 of 2 12 LastLast
Results 1 to 10 of 13
Like Tree17Likes

Thread: First restoration, a John Primble «Blue Grass»

  1. #1
    Junior Member
    Join Date
    Jan 2014
    Posts
    3
    Thanked: 0

    Smile First restoration, a John Primble «Blue Grass»

    Hi! I restored my first straight razor this Christmas, an ebay bought John Primble «Blue Grass». This forum and the wiki-pages were indispensable at all stages of the restoration, and I registered and posted this to show my appreciation to the community here.

    The razor started out with broken scales, rust, patina and dirt everywhere – the usual, as I've come to understand. My goal wasn't to make a showpiece, but rather to breathe some much needed life into the tool so that it can once again return to duty. Prior to purchasing this razor I bought a splendid Geo. Worthington, but it desperately needed a friend.

    Name:  john_primble_blue_grass_prior.jpg
Views: 478
Size:  56.4 KB

    From what I can tell, the razor is from sometime after 18901, sold by W.B. Belknap Hardware and made by H. Boker. I'm not intimately familiar with grinds, but I appears to be hollow ground. There was limited and even hone wear, so I imagine that the blade has several decades of usage left in it. The off-putting part about the blade was that the tang was asymmetrical and tapered only on one side. This made the fitting process more complicated than necessary, and the blade was ultimately not one hundred percent centered.

    There is probably not much I can tell you about the actual restoration. The blade I just polished using normal chrome polish. I probably should have sanded it down first, but I didn't want to ruin the etching so I skipped that part. I might go back later and put a proper polish on it if I find that it rusts easily. I made a set of scales from some ipe I had laying around, and a wedge from osage orange. Both woods are quite dense, and hard to work by hand, but elbow grease goes a long way. I'll probably get some powertools before doing another one. I shaped the scales using a farrier's rasp and by sanding, and finished it by sealing the surface with CA, sanding it more and, finally, buffing it with some white compound. As I said, the advice from the stickied restoration threads2 were invaluable, and in general things went smooth.

    CA sealed ipe takes a great polish – it if weren't for the weight and stiffness of the scales you'd think it was plastic. The osage orange provides a nice contrasts to the ipe, but it'll probably darken with age. Polished ipe is surprisingly interesting. The pictures doesn't really do it justice, but there's some nice subtle movement there.

    Name:  john_primble_blue_grass.jpg
Views: 475
Size:  16.8 KBName:  john_primble_blue_grass_front.jpg
Views: 485
Size:  21.2 KB


    I honed it today and took it for a spin. It shaves great! Thanks everybody!


    1. http://straightrazorpalace.com/razor...tml#post116220
    2. http://straightrazorpalace.com/works...wers-here.html

  2. #2
    Senior Member blabbermouth tintin's Avatar
    Join Date
    Jun 2013
    Location
    archbold ohio
    Posts
    2,363
    Thanked: 545

    Default

    very nice job. looks like you've been at it for years!

  3. #3
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,250
    Thanked: 3221

    Default

    A job well done and the scales look terrific for fit, finish and peening.

    Bob
    Life is a terminal illness in the end

  4. #4
    Always Thinkun walleyeman's Avatar
    Join Date
    Nov 2012
    Location
    Grain Valley, Missouri
    Posts
    818
    Thanked: 348

    Default

    Very well done! I like that you just polished the blade!! You have left the character intact! The blade is a short story when the resto is minimal!
    Scales superb!!

    Ray

  5. #5
    Senior Member MattCB's Avatar
    Join Date
    Jul 2013
    Location
    Kitsap County, WA USA
    Posts
    1,549
    Thanked: 351

    Default

    That's a great looking blade. Well done!
    The older I get the more I realize how little I actually know.

  6. #6
    Senior Member tiddle's Avatar
    Join Date
    May 2012
    Location
    Oxford, Al
    Posts
    1,605
    Thanked: 407

    Default

    excellent job for your first.
    Mastering implies there is nothing more for you to learn of something... I prefer proficient enough to not totally screw it up.

  7. #7
    Senior Member mycarver's Avatar
    Join Date
    Apr 2011
    Location
    Bethlehem, Pa.
    Posts
    950
    Thanked: 555

    Default

    Very nice work. Ironically I just got one in for honing. Hadn't seen one before and now here are two of them.
    Unfortunately the etch and gold wash on this one is a little tired but there.

  8. #8
    Senior Member traps38's Avatar
    Join Date
    Dec 2012
    Location
    MONTREAL/CANADA
    Posts
    158
    Thanked: 10

    Default

    Can't believe that's your first.

    Gorgeous,just gorgeous.

    Congrats.
    *****HAVE A GREAT SHAVE*****

  9. #9
    Junior Member
    Join Date
    Jan 2014
    Posts
    3
    Thanked: 0

    Default

    Thank you all for the kind words! It's clear from browsing these parts of the forum that I still have much to learn. SRP appears to be pretty much soaked in craftsmanship.

    Still, bringing this ol' fella back to life really gave me a taste for this.

  10. #10
    lz6
    lz6 is offline
    Senior Moderator lz6's Avatar
    Join Date
    Feb 2010
    Location
    California
    Posts
    4,833
    Thanked: 1841

    Default

    Nice job. And you are right there is a lot to learn here. Bringing these older discarded straights back to life is a mission for many of our members. Welcome.
    Bob

    "God is a Havana smoker. I have seen his gray clouds" Gainsburg

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •