Results 1 to 9 of 9
Like Tree10Likes
  • 1 Post By Magpie
  • 1 Post By biglou13
  • 2 Post By Steel
  • 1 Post By biglou13
  • 3 Post By boz
  • 1 Post By kelbro
  • 1 Post By DaveW

Thread: Soft ark

  1. #1
    Senior Member
    Join Date
    Jan 2019
    Location
    north florida
    Posts
    125
    Thanked: 10

    Default Soft ark

    First time with soft ark. It is very thirsty.

    give it a quick soak?

  2. #2
    Senior Member jfk742's Avatar
    Join Date
    Jan 2015
    Location
    Pinole, ca
    Posts
    1,526
    Thanked: 339

    Default

    Shouldn’t hurt it. Are you using oil or water?

  3. #3
    The First Cut is the Deepest! Magpie's Avatar
    Join Date
    Feb 2010
    Location
    Upper Middle Slobovia NY
    Posts
    2,736
    Thanked: 480

    Default

    I have so very many stones, and not a single soft ark among them. Realizing this now, makes me sad. And curious.... Looking forward to more replies to this thread.
    JOB15 likes this.

  4. #4
    Senior Member
    Join Date
    Jan 2019
    Location
    north florida
    Posts
    125
    Thanked: 10

    Default

    The soft ark and trans ark have been with me only 1 day. While I’ll already in love with the translucent black ark. I’m not sure about the soft, good thing it wasn’t expensive, It feels like it will leave coarse marks.... Maybe it was bad luck on My draw, I understand there can be large variances from stone to stone. ..... I’m not yet passing final judgement, i’ll Need to spend more time with it..... but the hard ark has made up for it! im using ballistol water mix
    Last edited by biglou13; 05-30-2019 at 03:20 AM.
    Steel likes this.

  5. #5
    Senior Member blabbermouth Steel's Avatar
    Join Date
    Nov 2013
    Posts
    2,321
    Thanked: 498

    Default

    A brand new soft ark can feel rather coarse. You can burnish the surface just a bit to tame it down or let it tame on its own. If you hone a knife or two on it that usually smooths it out some.
    What a curse be a dull razor; what a prideful comfort a sharp one

  6. The Following User Says Thank You to Steel For This Useful Post:

    biglou13 (05-30-2019)

  7. #6
    Senior Member
    Join Date
    Jan 2019
    Location
    north florida
    Posts
    125
    Thanked: 10

    Default

    Quote Originally Posted by Steel View Post
    A brand new soft ark can feel rather coarse. You can burnish the surface just a bit to tame it down or let it tame on its own. If you hone a knife or two on it that usually smooths it out some.
    I have a few chef knives that could use a touch up.
    And I think the soft ark would be perfect for this!
    Steel likes this.

  8. #7
    boz
    boz is offline
    Senior Member boz's Avatar
    Join Date
    Aug 2017
    Location
    Loveland, Colorado
    Posts
    224
    Thanked: 41

    Default

    When I have a razor that is pulling a bit I sometimes go to my soft Ark then Black Ark. I use oil on my Soft Ark. It is lapped with 320 Silicon Carbide about every tenth use, based on scratch pattern I would rate it about the same as my 8K synthetic. Some day I will burnish the bottom and see what that scratch pattern looks like.
    A healthy skepticism of both old and new ideas is essential to learning.

  9. The Following User Says Thank You to boz For This Useful Post:

    biglou13 (05-30-2019)

  10. #8
    Senior Member kelbro's Avatar
    Join Date
    May 2008
    Location
    N. Carolina
    Posts
    1,352
    Thanked: 181

    Default

    Kitchen knives do well on soft arks. Once the stone has 'burnished' a little, then use it for your razors.
    ScoutHikerDad likes this.

  11. The Following User Says Thank You to kelbro For This Useful Post:

    biglou13 (05-30-2019)

  12. #9
    Senior Member blabbermouth
    Join Date
    Jul 2011
    Posts
    2,110
    Thanked: 458

    Default

    Who marketed the soft ark? They are drastically different from one seller to the next, and I've got some experience with some of the older labeled stones (smiths, case, etc) so I can give you an idea of what you're working with.

    Dan's softs aren't that great, but they might be OK for razors. They're on the fine and slow side. The old multicolored stones that came in plastic boxes with "case" brand on them were supremely coarse. The natural whetstone company at least the last time I bought sold something that was between the two.

    Norton's softs tended to be a little on the fine side, too.

    When you're scuffing them, mind the razor bevel - loose particles can get above the bevel and leave little scratches all over just above it into the hollow. They don't go far into the hollow, but they're visible.
    biglou13 likes this.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •