Page 1 of 2 12 LastLast
Results 1 to 10 of 17
Like Tree20Likes

Thread: Oil on a water stone!!! Are you crazy!!!!

  1. #1
    I love Burls....... and Acrylic HARRYWALLY's Avatar
    Join Date
    Mar 2012
    Location
    Baden, Ontario
    Posts
    5,475
    Thanked: 2284

    Default Oil on a water stone!!! Are you crazy!!!!

    So a couple weeks back I had my 1000 grit water stone at work to put an edge on my wood chisel. Of coarse I left it back by the grinder over night. The next day I show up for work, go back to grab my hone and a coworker had used it with 3 in 1 oil. Not just a bit, a ton! Naturally, smoke starts shooting from my ears!!

    Now, I wouldn't call myself a hone expert, but I'm pretty sure the box didn't say water and oil hone. It just said WATER!!!! Another reason I'm so ticked is this was my grandfather's stone I got from him when he passed away when I was 16. I've had this stone for 17 years and I'm not sure what I'm going to do with it. It seems as though the oil is gone now but, it doesn't cut like it use to. It takes wayyyy to long for anything to happen.

    What should I do fellas?
    Burls, Girls, and all things that Swirl....

  2. #2
    Senior Member blabbermouth Hirlau's Avatar
    Join Date
    Dec 2010
    Location
    South Florida
    Posts
    13,530
    Thanked: 3530

    Default

    I would soak & scrubb with Simple Green a few times.
    Just my thoughts.
    HARRYWALLY likes this.

  3. The Following User Says Thank You to Hirlau For This Useful Post:

    HARRYWALLY (10-10-2012)

  4. #3
    I love Burls....... and Acrylic HARRYWALLY's Avatar
    Join Date
    Mar 2012
    Location
    Baden, Ontario
    Posts
    5,475
    Thanked: 2284

    Default

    Quote Originally Posted by Hirlau View Post
    I would soak & scrubb with Simple Green a few times.
    Just my thoughts.
    Simple Green stone cleaner probably?
    Burls, Girls, and all things that Swirl....

  5. #4
    ..mama I know we broke the rules... Maxi's Avatar
    Join Date
    Feb 2010
    Location
    Toronto, Ontario, Canada
    Posts
    2,895
    Thanked: 993
    Blog Entries
    8

    Default

    Maybe try putting it in a bag of white rice. That may pull out some of the oil and moisture.
    HARRYWALLY likes this.

  6. The Following User Says Thank You to Maxi For This Useful Post:

    HARRYWALLY (10-10-2012)

  7. #5
    Senior Member blabbermouth Hirlau's Avatar
    Join Date
    Dec 2010
    Location
    South Florida
    Posts
    13,530
    Thanked: 3530

    Default

    The Simple green found in stores, it's a good bio safe (it says) degreaser. I have used it on many stones.

    I have not used it on my white Norton 4000, though.

  8. #6
    The First Cut is the Deepest! Magpie's Avatar
    Join Date
    Feb 2010
    Location
    Upper Middle Slobovia NY
    Posts
    2,736
    Thanked: 480

    Default

    On a stone like a 1000 grit, I would try this favorite trick of mine...

    wrap stone in a few layers of paper towel. Place stone in electric toaster oven. (make sure paper towel doesnt pop up anywhre and touch heater coils)
    Set at 200 degrees
    After 2 hours, raise temp to 250 degrees
    After 2 hours, Lower temp back to 200 degrees
    After an hour, turn off, and allow to cool to room temp without opening the door to the oven.
    You will find that the warm oil has migrated through the stone, and seeped into the paper towel
    I know it seems like a lot of work, but I am cautious (perhaps unnecessarily so) of thermal stresses causing fractures in the stone.
    After that, you can soak it in a bucket of soapy water, to help float out and dissolve any remaining oils.
    Hirlau and HARRYWALLY like this.

  9. The Following User Says Thank You to Magpie For This Useful Post:

    HARRYWALLY (10-10-2012)

  10. #7
    I love Burls....... and Acrylic HARRYWALLY's Avatar
    Join Date
    Mar 2012
    Location
    Baden, Ontario
    Posts
    5,475
    Thanked: 2284

    Default

    Quote Originally Posted by Magpie View Post
    On a stone like a 1000 grit, I would try this favorite trick of mine...

    wrap stone in a few layers of paper towel. Place stone in electric toaster oven. (make sure paper towel doesnt pop up anywhre and touch heater coils)
    Set at 200 degrees
    After 2 hours, raise temp to 250 degrees
    After 2 hours, Lower temp back to 200 degrees
    After an hour, turn off, and allow to cool to room temp without opening the door to the oven.
    You will find that the warm oil has migrated through the stone, and seeped into the paper towel
    I know it seems like a lot of work, but I am cautious (perhaps unnecessarily so) of thermal stresses causing fractures in the stone.
    After that, you can soak it in a bucket of soapy water, to help float out and dissolve any remaining oils.
    I like the sounds of this. Ill give it a try.
    Burls, Girls, and all things that Swirl....

  11. #8
    Senior Member Eekspa's Avatar
    Join Date
    Aug 2012
    Location
    Fiddletown, California
    Posts
    222
    Thanked: 32

    Default

    First thing you do is drop a 10# sledge on top of the idiots toes. Next time he will leave your tools alone. Then you can follow the good suggestions above.
    Any day on this side of the flowers is a good day!

  12. #9
    ace
    ace is offline
    Senior Member blabbermouth ace's Avatar
    Join Date
    Dec 2010
    Location
    Virginia
    Posts
    3,362
    Thanked: 581

    Default

    Quote Originally Posted by Maxi View Post
    Maybe try putting it in a bag of white rice. That may pull out some of the oil and moisture.

    Even if the rice looks tasty, don't eat it!

  13. #10
    Senior Member blabbermouth
    Join Date
    Jul 2011
    Posts
    2,110
    Thanked: 458

    Default

    What brand of stone is it? We can't really give you an accurate procedure to follow if we don't know what kind of stone it is.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •