Results 11 to 19 of 19
Thread: Big success
-
03-24-2017, 07:49 PM #11
Just tried out the Hunter and it was about midway between the Boker and the Wosty so I guess I was getting better each time
-
03-24-2017, 07:54 PM #12
-
03-29-2017, 12:19 PM #13
Just an update on this.
Saturday I use dthe IXL again and it didnt go well. My wife kept calling on me to do this or that and I had a horrible shave, lot so tugging, nicks and not smooth at all. Dammit why cant women understand you NEVER EVER disturb a man when he is in the bathroom unless it is to join him in the shower.
Tuesday after my face had healed I tried it again when no one was home. Like the first time ultra smooth, I actually stopped a few times to feel my face because there was no resistance and not even any of the usual noise of the whiskers being cut
The only razor I have that comapres is my grandfathers Sansouci that Outback restored for me, just as smooth but I can hear the screams of my whiskers as it decapitates them
-
03-29-2017, 02:30 PM #14
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215Try finishing on the 12k Naniwa, and leave the Welsh Slate out of the progression. You are probably going backwards in grit with it.
A properly stropped 12k Naniwa edge is a fine shaving edge, if you need a little more, some Chrome Oxide will get you there.
-
03-29-2017, 03:34 PM #15
- Join Date
- Dec 2014
- Location
- Virginia, USA
- Posts
- 2,224
Thanked: 481I love my Welsh slates but...I'll second this. Especially if you're stropping on any sort of pastes. I don't know what the ones you've got are comprised of, but they're more than likely erasing anything you did with the Welsh slate. If you like the edge you're getting off the pastes you can likely cut the slate out of the regimen and save yourself some effort/time.
Personally I enjoy my natural finishers, so I don't use pastes outside of the one razor I've set aside as a test bed for them.
-
03-29-2017, 04:46 PM #16
-
03-29-2017, 09:56 PM #17
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215So, if you are not getting a shaving edge from a Naniwa 12k, then something else is going on with your technique.
To trouble shoot your technique, eliminate all the variables or as many as you can. A Natural stone of unknow grit, used with or without slurry is a huge variable.
A Naniwa progression is a bullet proof progression and a Naniwa 12k is a proven shaving edge, it is pretty much the current Gold Standard.
Set yourself up for success with a proven finisher. Once you master a synthetic technique, then introduce naturals finishers. You will quickly know if any issues are the stone or technique.
Look straight down on the edge, any reflection on the edge are where the bevels are not meeting. Depending on what you see, re-set the edge on the 5 or 8k and finish on the 12k.
-
03-29-2017, 11:52 PM #18
No I am getting good shaves off the 12k naniwa but not the same level as when I started using the Welsh slate.
As to technique it is definitely getting better, perhaps that is despite the Welsh slate
I suppose the next ones I could do some with the Welsh slate some without and see what happens.
-
03-30-2017, 12:36 AM #19
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215Finish on the 12k, and shave. Re-finish the same razor on the Welch and shave.
If worst, just re-finish on the 12k, again and you are good.
Using slurry is/can be difficult to learn and can vary with each stone and the razor. You will have to learn each stone and the slurry, how and how much to slurry for the effect you want.
Finishing on slurry, from a 12k edge is very different from a one stone hone, from a 1k to finish or even from a 4-5k to finish.
How you raise your slurry(s) Diamond Slurry, tomo or other slurries, will also affect performance, as will water only finishes. You just have to experiment. And keep in mind that a Ebay Welch slurry is very different from a Coticule, Escher and finish Jnat, those techniques may or may not work.
I find that finishing on slurry, from a, 8 or 12k, start with a thin slurry and adjust, as needed.
-
The Following User Says Thank You to Euclid440 For This Useful Post:
AlanQ (03-30-2017)