Printable View
This blade is dull. But have i used only the one side all the time?
I feel silly asking this but i am loosing track of which side of the DE is getting the work. I can see myself using only one side and tossing a "half used" blade away.
I have started laying the last used side down and using the upward facing side the next day.
With a straight there is no choice....
Here's the crazy way I do it.
I take one stroke, the roll it over for the second stroke, rinse, repeat untill the shave is done.
Then I open the razor, remove the blade with my left hand, use a wet Q-tip with my right to wipe the residue for both edges & both sides, then place it back in the same way it came out.
I'm getting 6 good shaves out of a Shark & 7 or 8 out of a feather before I put a new blade in. I could probable get more shaves out of each, but I'm working my way through a sample pack, so I can't wait to test the next brand.
That's the reason I quit using a DE. I could never figure out which side of the blade got the most passes. When the wife found me counting strokes with a magic marker on the bathroom wall, out went the DEs.
I use them however it comes, then take out the blade hand strop on my palm. Blades go for as long s they go and there is no difference in how each side shaves as far as I can tell.
There are much bigger things in life to worry about.
I never remove the blade till the end of her life
In shaving after the first pass from the cork i use both sides
I never turn upside down the blade cause i think will make the cut a little bit different
Practically a shaver must be a Super-Expert to understand the difference if someone turn the blade without to know it so i do it first for psychological reasons and second due to "machinist rules".
:nj
I generally flip sides, each half pass. I do the right side, flip the razor, do the left. I am sure that I occasionally end up with slight uneven wear, but I tend to toss blades, especially DE blades very quickly, so a "good enough" system fits my needs.
i use one side on one side of my face , and the other on the other side ..
Ditto the last two replies.
Mick
i thought the reason for two edges was so that when one side gets loaded up with lather you can use the other and rinse the razor half as much. i've been flipping the blade over after each use and i thinks it helps it last longer.IMHO
I'm not a DE shaver but reading this thread I can't help be be left wondering; How expensive are those blades?
Not all of us are big spenders!:) The little bit I have used a DE has been with Walgreen special blades or similar. By accident I ran into a store while looking for another shop for ingredients for an aftershave that had Merkur blades. $8 or so for pack may not have been a deal as the other things in that store where expensive but what the hay. I don't know and didn't care.Quote:
Originally Posted by thebigspendur
To me it is more of a matter of principle. Even if half is only 40 cents why throw something half used away? Using a blade a week for example for me that is about an hours wages after taxes per year. I can waste that money on something else! One 5th of one months truck payment maybe.
They are not expensive. The Sharks are good enough for me, even though I keep a lot of Feathers on hand. It's more about getting the most out of each blade. I order online my DE blades, cheaper & better than what's offered at Wal Mart.Quote:
Originally Posted by RezDog
+1, that is what I do. When the blade starts to dull after a few shaves I'll remove the blade and flip it (possibly palm strop it as well), which usually gets me another couple shaves from a blade before I toss it.Quote:
Originally Posted by tintin
I seem to average 4-6 shaves from a blade, which is better than the 3-4 I used to get before adopting this technique but that's the max for me. I'm not one of the guys who manages 8-10 shaves from a single blade.
ill have to try that , im at the 3-4 with any blade ive tried .. thanks !Quote:
Originally Posted by Ryan82
$.1 to $.4 a blade. The feather has been the most expensive I have seen but I have found on ebay they can go under $40 per 100 blades so if you find the right deals $.9 to $.32. At that rate I don't worry about even or uneven wear. Depending on the blade I toss it into the tin I use for a blade bank after 3 or 5 shaves. Compared to cartidge razors this still is a huge saving.Quote:
Originally Posted by RezDog
Granted the least expensive in the long run is a straight. Much higher start up cost for razor, strop, and hone but you don't have to pay anything else for a long time. Hones last a long time as do strops. If you learn how to hone properly your only expense afterward is a new hone when yours wear done and a new strop is yours is damaged. Blades are a lifetime expenditure. The other problem is it takes more practice and skill to use a straight. I have gotten to where I can shave wtg with no problems but nick alot with xtg and atg. The size of the blade just makes it harder to get in some areas with a "sideways" stroke.
When I need to use a DE because of excessive razor burn from a Str8 I use an Astra blade. If you look the edges are numbered in the corners 1, 2, 3, 4. Easy to remember which edge I used and I change edges after 3 or 4 uses. Not bothered by often need to rinse. Gives me a chance to check progress of shave, i.e. more lather needed, what nicks, how close so far (and a quick look in the mirror to see if I'm watching myself bleed to death LOL).
I used to drive myself crazy obsessing on such details. Especially, how many shaves have I got on this blade. I decided to quit worrying about it, now I use the other edge when the one I'm using is loaded, and I shave with a blade until the first stroke it starts to not shave very comfortably.
After trying many blade ....Lords do it for me. dont seem to see many a mention of them on various forums i read.