Printable View
Ok not sure where to put this as it is a strop but not in the traditional sense, and it is related to DE but not in the sense of actually shaving. So here goes.
I have a KrisKross strop and would like to know how to refresh the leather strop disc in it. I think I can lightly sand it to smooth the surface but not sure if others could offer advice. Any idea of how to take it apart?
if it is not in the correct forum heading let me know.
I'm just curious about this device. Could you post a picture?
here is a link to pictures,
Shaving Collectibles
This is not mine but middle one is the same box ect.. as mine.
I figured it out. The bottom peice will come off, it has little notches that have seats that it turns into. once the bottom is off you can unscrew the strop and backing plate. I will put some pictures up oif I get a chance and if I can do the picture thing on this forum.
Hi,
Do you find they actually sharpen a DE blade well enough to use for a few more shaves, or do you count them as more of a novelty to keep on display?
I picked up a Kriss Kross stropper pretty cheap and tried it out with a used DE blade I have. I felt it sharpened the blade a tad on the rough side. I'm not naive enough to expect it to create a perfect edge, but I thought it might have done a bit better.
That brings me to my final question: I was curious how you actually got the back plate off so you could recondition the leather disk. My back plate is on so tight I don't think I could get it off with anything less than C4 ;)
Regards,
Charles
Charles
I will attempt o answer your questions.
1) I do think it will extend the useful life of a DE blade. I also tried with used blades, a couple seemed much better, a couple seemed none better if not a bit worse.
2) getting the bloody thing apart was a puzzle. You will see around the edge that there are indents that have a push in and turn look. There will also be one spot where there is a small indent to prevent rotation. I just put a small screw driver in between the bottom and main case and it allowed me to unlatch the indent and turn the case. The case then will seperate. I was then able to unscrew the backing plate and strop leather. make sure you don't lose the spacer ring or let the crank fall out.
3) I refurbished the strop with 220 then 320 sand paper with the disk on a flat secure backing (plate glass). I have only put vitamin E oil on as a dressing. I may need to use some type of strop paste, but I do not know anything about strop paste so let that be your guide.
does any of that help?
Thanks Scrapcan, that does help! I'm glad to see this little beastie does hold potential value for sharpening the occasional DE blades. What can I say...I'm cheap :pQuote:
Originally Posted by scrapcan
I followed your screwdriver suggestion and it seems that all I'm able to do is make tiny nicks in the metal, so I'm going to stop while I'm ahead. I really don't want to break it...it's in really nice condition and I'd like to keep it that way :D
The unit I have came with instructions stating that you should use a few drops of Neatsfoot oil or Olive Oil on the leather and rub in with a cloth once or twice a year to keep it supple. I used a few drops of Olive Oil and it seems to be ok.
I'll probably try messing around with it again once I find a smaller screwdriver.
Regards,
Charles
Charles,
You go the right idea youjust need a better fitting tool. I used a small flat blade and studied the edge to see where a pin is located to get it loose. it will come apart I promise.
My instructions say to put some lather on it once or twice a year. Since I had to take it apart and sand the surface I was not sure if just lather would do it. I may have to try it though.
I got a notice from another member asking how I got the leather disc and back plate off. I tried to respond, but there is no email address in notification and the respond form is not working with my version of safari.
So I hope you see this Josh.
Once you get the back off you will see the backing disc and in center is the screw. This screw attaches to the crank. Hold the strop per upside down in your hand, it helped me to have blade carrier in the up position, with crank between you thumb and index with index between blade carrier and frame.
The looking at bottom side turn counter clockwise. I was able to push down with fingers on other hand and turn at the same time. You do have to hold the crank.
Let me know if you need more help.
Hi all. Newbie to your forum. I picked up a Kriss Kross a couple of weeks ago. I have been following this thread trying to get the dang thing apart. I can't find a decent tab to release. There are five obvious detents but none looks like a release. Can/will someone post a picture of the decent to release the bottom? Thanks in advance
qanerd
I gave my stropper to another member some time ago. I looked through my photo archive and did not take pictures of the ktiss kross. Look closely at the bottom cover plate, you should see how it works. It will come off
These things are neat! I have one to show folks.
The old blades were carbon steel. The leather in these things was new back then as well!
New, modern blades would not benefit much, if at all, even if the leather was new?
Still pretty fun to see the clockwork blade flipping.
A fella I work with has one and even what he says is a Kriss Kross razor, no matter what I offer he will not sell to me he likes the mechanical aspect too much. I am going to show him my Rolls Razor so we can have a mechanical show down :D