Page 1 of 2 12 LastLast
Results 1 to 10 of 20
Like Tree54Likes

Thread: sterilising antique razors

  1. #1
    Junior Member
    Join Date
    Aug 2018
    Location
    Queensland
    Posts
    2
    Thanked: 0

    Question sterilising antique razors

    hello,

    Im new to using a straight edge razor and am wanting to get an antique one from a shop down the road.. what is required in regards to sterilising the blade?
    Substance likes this.

  2. #2
    Senior Member blabbermouth
    Join Date
    Jun 2013
    Location
    Pompano Beach, FL
    Posts
    4,014
    Thanked: 631

    Default

    Are you going to sand and polish the blade and then hone? If it is not shave ready you may need to have it honed. I use Lysol Disinfectant spray. I spray the blade well and let it sit 10 minutes or more. If you want you can repeat again as insurance. If you are sanding and polishing then honeing you will be removing enough metal that you should be good to go.

  3. The Following User Says Thank You to bouschie For This Useful Post:

    Valthorenzoe (08-25-2018)

  4. #3
    boz
    boz is offline
    Senior Member boz's Avatar
    Join Date
    Aug 2017
    Location
    Loveland, Colorado
    Posts
    224
    Thanked: 41

    Default

    I use a product called Barbicide.
    Substance, outback and Gasman like this.
    A healthy skepticism of both old and new ideas is essential to learning.

  5. The Following User Says Thank You to boz For This Useful Post:

    Valthorenzoe (08-25-2018)

  6. #4
    Senior Member blabbermouth
    Join Date
    Jun 2013
    Location
    Pompano Beach, FL
    Posts
    4,014
    Thanked: 631

    Default

    Be very careful not to get the Barbicide on the scales. Use on blade only.
    outback likes this.

  7. #5
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,383
    Thanked: 4820

    Default

    Straight up rubbing alcohol.
    It's not what you know, it's who you take fishing!

  8. The Following 2 Users Say Thank You to RezDog For This Useful Post:

    sharptonn (08-26-2018), Valthorenzoe (08-25-2018)

  9. #6
    Senior Member blabbermouth Geezer's Avatar
    Join Date
    Jul 2010
    Location
    EauClaire,WI
    Posts
    7,685
    Thanked: 3825
    Blog Entries
    1

    Default

    Off the wall but it works:
    Wash with "Dawn" or a citrus liquid.
    Then rinse well and ;
    Dip it completely into 190proof Vodka ( Much cheaper than "Everclear!"
    Open and close it while wet with alcohol and use a blow-drier to dry it. At a distance!
    JMO
    YMMV
    ~Richard
    JOB15, outback and Gasman like this.
    Be yourself; everyone else is already taken.
    - Oscar Wilde

  10. The Following User Says Thank You to Geezer For This Useful Post:

    Valthorenzoe (08-25-2018)

  11. #7
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    Welcome the SRP. Guessing sense you are new the SR Shaving, that you dont know how to hone. Id recommend finding someone that is willing to hone both your razors first. When they do the honing, most will disinfect them before sending back. Learning to shave with a used vintage or even a new razor, the first step is to send them out for a proper HAND honing.
    Geezer, Substance and outback like this.
    It's just Sharpening, right?
    Jerry...

  12. The Following User Says Thank You to Gasman For This Useful Post:

    Valthorenzoe (08-25-2018)

  13. #8
    Senior Member
    Join Date
    Nov 2016
    Location
    Chicago Suburbs
    Posts
    1,091
    Thanked: 292

    Default

    Although ethyl alcohol and isopropyl alcohol are slightly different chemically, they are quite similar in their disinfectant ability. For this application, the most effective concentration is 70% (140 proof in the case of ethanol). Higher concentrations evaporate quickly and my not have sufficient time to do their job. Lower concentrations may not be strong enough to do the job. If you subscribe to Geezers suggestion of using 190 proof vodka, be sure to soak the blade for at least 10 minutes before drying.

    Neither one of the common alcohols are effective against fungal or bacterial spores, but with a steel blade, scrubbing the blade with a toothbrush and soap should remove any spores.

    Others have recommended Barbicide. It is a high-level disinfectant used in hospitals to kill a variety of bacteria, viruses, fungi, etc. Even some of the tougher candidates like MRSA are killed. Since a small bottle of Barbicide is inexpensive (less than $10 for 16 oz), it is a bargain. Furthermore, you dilute 2 oz of Barbicide with 32 oz water before using. Thus, a 16 oz bottle is enough for eight batches at a cost just slightly over $1 per batch. If it is good enough for hospitals and barbers, I figure it is good enough for me.

  14. The Following 3 Users Say Thank You to RayClem For This Useful Post:

    bluesman7 (08-26-2018), JBHoren (08-25-2018), Valthorenzoe (08-25-2018)

  15. #9
    Junior Member
    Join Date
    Aug 2018
    Location
    Queensland
    Posts
    2
    Thanked: 0

    Default

    Thank you,

    yes I intend to get it honed, however I'm in Australia in Queensland I'm still in the process of trying to find someone that will hand hone it. The razor already feels pretty sharp, and I'm wondering how it will come up after just being put on a strop..
    I don't understand how a strop works? if you get the razor honed, what use is putting on the strop?

    Thanks for the advice
    Geezer likes this.

  16. #10
    Senior Member blabbermouth markbignosekelly's Avatar
    Join Date
    Dec 2012
    Location
    Egham, a little town just outside London.
    Posts
    3,725
    Thanked: 1074
    Blog Entries
    2

    Default

    First of all welcome to SRP!

    Second, read everything here https://shavelibrary.com/w/Shave_Library

    Third, when you get your razor, PM onimaru55, im sure he'll help you if he can.
    Geezer and JOB15 like this.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •