Maher & Grosh in horn from start to finish (Pic heavy!)

I've been thinking about doing this for a while, but knowing it would take a ot of time I've been postponing it over and over again, but this weekend I finally decided to go for it, so here is a "How do I do it, step by step" taking a Maher & Grosh from start to finish.

1. Here's the raozor as it came to me, pretty good shape, except for someone trying to sand it or something making some light scratches along the blade and the scales had started to shrink, which is not a very good sign being celluloid....

http://i1212.photobucket.com/albums/...ps3b7799cc.jpg

2. Unpining. Cutting the pins of with a flush cutter, then using a mandrel to carefully drive them out.

http://i1212.photobucket.com/albums/...ps7b8e15c6.jpg
http://i1212.photobucket.com/albums/...ps154a8fd8.jpg

3. Blade out of the scales, ready for buffing.

http://i1212.photobucket.com/albums/...psd3f309aa.jpg

4. My buffer. I use these tapered spindles, making wheel change fast and easy.

http://i1212.photobucket.com/albums/...pse085c6c9.jpg
http://i1212.photobucket.com/albums/...psa1a1e658.jpg


5.Buffing. Since this blade was in pretty good shape I only ran it very lightly on 400 grit greaseless before moving on trough four different steps of polishing.

http://i1212.photobucket.com/albums/...ps06087039.jpg

6. Blade finished.

http://i1212.photobucket.com/albums/...ps396e503d.jpg

7. Then to making sales. This is the horn I had picked out for this one, it's not very good pieces, quite curved, uneven and flaking, so I had to sand it flat and could only get on scale out of each piece, making a bit more work than with a good piece.

http://i1212.photobucket.com/albums/...psdf0898ae.jpg
http://i1212.photobucket.com/albums/...psaa39fa90.jpg

8. Safety - wear gloves!!

http://i1212.photobucket.com/albums/...psae1366e3.jpg

9. The horn is ready, lying on the bench waiting for a design. When making custom scales I outline the blade on a piece of paper and sketch the scales around it to make sure the size is correct. The shape I draw is not necessary the final shape, for this one I just drew the basic "square" shape and rounded it a bit when sanding them as you will see later.

http://i1212.photobucket.com/albums/...ps9e80b05c.jpg
http://i1212.photobucket.com/albums/...ps15e0f1c7.jpg

10. Transfering the design to the back scale with carbon paper.

http://i1212.photobucket.com/albums/...psdac930c2.jpg

http://i1212.photobucket.com/albums/...psbaf5b609.jpg

11. Attaching the desing to the horn with double sided tape.

http://i1212.photobucket.com/albums/...psf49f154c.jpg

12. Rough cutting the scales on a Scroll saw.

http://i1212.photobucket.com/albums/...ps88e0d831.jpg

http://i1212.photobucket.com/albums/...ps3dcacbc9.jpg

13. Attaching the two pieces together with double sided tape.

http://i1212.photobucket.com/albums/...ps2c0bb2f0.jpg

14. Drilling holes for the pins.

http://i1212.photobucket.com/albums/...psbf2c0a90.jpg

15. Shaping the sales on the belt sander.

http://i1212.photobucket.com/albums/...ps1c96b049.jpg

16. Main shape is ready, here I change to a 180 grit belt for the final thinning and shaping.

http://i1212.photobucket.com/albums/...ps8ba1e208.jpg

17. Finished with the belt sander, now to hand sanding up to 2000 grit.

http://i1212.photobucket.com/albums/...ps36c4a09e.jpg
http://i1212.photobucket.com/albums/...ps37f2c450.jpg

18. Hand sanded to 2000, ready for polishing. I use Autosol (Equal to Maas etc. for polishing most materials)

http://i1212.photobucket.com/albums/...psab288166.jpg
http://i1212.photobucket.com/albums/...ps624f9ddf.jpg
http://i1212.photobucket.com/albums/...ps857fcf51.jpg

19. Splitting the scales. For this I use a cracked blade, the concave shape of the hollow grinde makes it easy without putting too much pressure on the materials.

http://i1212.photobucket.com/albums/...psee3cce2d.jpg

20. Making the wedge. I'm using bone for this one, here I make the "V" shape using the belt sander.

http://i1212.photobucket.com/albums/...psb19a8ec5.jpg

21. Drawing the outline of the scale onto the wedge and marking the pin hole. Then rough cutting on the scroll saw before shaping it on the disc sander.

http://i1212.photobucket.com/albums/...psdde051e8.jpg
http://i1212.photobucket.com/albums/...pse4376132.jpg
http://i1212.photobucket.com/albums/...psd1370ca8.jpg

22. Mocking the mount of wedge and blade to make sure I got the flex I want in the scales and that everything fits as it should.

http://i1212.photobucket.com/albums/...ps09c0ca53.jpg
http://i1212.photobucket.com/albums/...ps6a1f60d8.jpg

23. Pining the wedge.

http://i1212.photobucket.com/albums/...ps7e51a6e9.jpg

24. Sanding the wedge flush to the scales...carefully....then hand sanding and polishing.

http://i1212.photobucket.com/albums/...ps97bbf3db.jpg
http://i1212.photobucket.com/albums/...pse4d12c08.jpg

25. All pinned up, almost done...

http://i1212.photobucket.com/albums/...pse633e259.jpg

26. One little trick for the final finish: I sand the pins with 2000 paper and polish them, the tape is t protect the scales from scratches.

http://i1212.photobucket.com/albums/...ps3a328b41.jpg
http://i1212.photobucket.com/albums/...ps37114468.jpg

27. Balance is everything...

http://i1212.photobucket.com/albums/...psadd81d3a.jpg


28. DONE!

http://i1212.photobucket.com/albums/...ps787658b5.jpg


Hope you enjoy this, thanks for looking.

Thanks for posting this useful how to series. She turned out very nice.

Bob

Beautiful work! Thanks for taking the time to document the process with photos and for sharing it with the community.

I am about to make some scales for myself. I've been a little hesitant, but now I think it'll be fun. Thanks for posting!

Very nicely done and an excellent presentation :tu

Those new scales really compliment the blade!

Thanks for taking the time to take us through the process. The pics show it all. Great work and a great looking razor as a result.

Quote:

---

Originally Posted by rplunk43

I am about to make some scales for myself. I've been a little hesitant, but now I think it'll be fun. Thanks for posting!

---

+1. I also found a video on you tube that was very similar to this. Great info. Thanks.

Very nice! Thanks posting this. The final product is excellent!

very nice,... thanks for sharing your workflow :)!

Absolutely a great looking razor, thanks for posting, I always wondered how a razor was balanced. That goes to prove you learn something new everyday.

Very nice! Great WIP as well. Thanks for sharing.

Very nice. Like the color change in the scales.

Great job on documenting the process on a very beautiful finished razor!

Beautiful work! and great write up!

Wonderful posts, thank you for sharing. Lovely to see shared methods around here so we can continue improving and modifying our own.

The words "picture heavy" are like promising free gold around here, and you sure delivered!

Very nice finished job
Great write up, well stepped out, gives a good base for the newb restorer
Thanks for posting

Well done Rune ! Shame the old scales were on the way out. They looked pretty great.

Quote:

---

Originally Posted by onimaru55

Well done Rune ! Shame the old scales were on the way out. They looked pretty great.

---

Thanks Oz.
I'd really liked to keep the original scales, but with celluloid started to shrink I just didn't want to take any chances. Too bad :(

Quote:

---

Originally Posted by Zephyr

Thanks Oz.
I'd really liked to keep the original scales, but with celluloid started to shrink I just didn't want to take any chances. Too bad :(

---

Yup, easier to replace the scales than the steel . :)

Great thread.
Enjoyed all the details.
Myron

That is awesome, very nicely done.

What compunds did you use to obtain that mirror finish?