To sand or not to sand...

Hello Gents,

I have this Imperial that I had been in search of for a while and am now getting around to working on it. There is some pretty harsh pitting but the etching is still in great shape. I have only done a mild clean up (WD-40, 000 steel wool, Mothers and a rag). Not sure if I want to sand it but I do want the etching to come back to life. What would you do? I do not mind pitting on an old razor as long as it is clean and not rusting anymore. I am just second guessing how far I want to take this clean up.

Bad pics I know
Attachment 239488

Tonight's pic

Attachment 239492

As you can see, it has pitting.


Thank You

The first thing I would do is take it to a 1K [Insert brand here] with tape and see how the pitting near the bevel cleans up before deciding anything else.

For the next little while tonight I am going to work on the edge. I have looked at it through a 60x loupe and it needs a bevel set. It has been honed poorly before and stored poorly after that. At least I didn't pay too much for it. I really like Imperials the others that I have took a great edge and hold them well, this is the worst shape I have started with.

Really cool etch! I wouldn't go much further maybe 1000 sandpaper. I wouldn't go much lower.

As 32T said, make sure the edge is ok before going much further

I have never seen an etch like that, nice find! Do some poking around here and you can find some great threads on preserving etches by people far more skilled than myself:) If I restoring and want to keep an etch I will usually just do a rough clean so I don't risk removing it.

Good luck, and post pictures of the finished product!

I'll go out on a limb and say that the edge will be fine.

I'll also say that I'd start with just some metal polish/Mothers Mag and Aluminum is my go to. You can always go coarser but once you do, it takes a lot of work and steel to go back up :w

Perhaps it's just the pic but there seems to be a problem at the heel. The Red shows the general area and the Blue shows the area in question.

Attachment 239506

Just an observation/I hope its of some help. :shrug:

Quote:

---

Originally Posted by cudarunner

I'll go out on a limb and say that the edge will be fine.

I'll also say that I'd start with just some metal polish/Mothers Mag and Aluminum is my go to. You can always go coarser but once you do, it takes a lot of work and steel to go back up :w

Perhaps it's just the pic but there seems to be a problem at the heel. The Red shows the general area and the Blue shows the area in question.

Attachment 239506

Just an observation/I hope its of some help. :shrug:

---

Yes it does have some issues on the heel, well it has some issues everywhere but the heel has a chip. That chip is far enough from the edge to make me think to just leave it alone. After some work on a Naniwa 1000 Professional, the bevel seems to be ok. Still needs work though.

Attachment 239512

I vote leave it, the etch will only be less evident. I have heard erasers are good for spot clean up

Cover the etching with nail polish after hitting the entire thing with Mothers or Maas. Then sand with 1000 grit if needed and work your way back to a nice polished look. Looks like it will be a nice one when your done.

+1 for using an eraser with the mag polish etc on it works great for getting around the etches & into corners & grooves like the pivot area on the spine etc
I got a large 4" x 1 1/2" rubber from a cheap shop & cut it down suit what I want

Hi, First time user of the forum,I hope I'm posting in the proper place, the etching is amazing, I would love to find a blade with anything cycling related. Yesterday I purchased 2 SR second hand, I don't have very muck knowledge on the pieces,I am afraid of losing (sanding) the hallmarks,stamps and engraving off the blades, basically I don't know where to begin, the edges feel and looks to be in shave ready (from what I can tell) any help or advice would be greatly appreciated,Best of luck on your beauty and hope everything turns out well. Thank you in advance.

Welcome from SE Washington State USA,

Pictures are almost a MUST! Please include some if at all possible.

Again Welcome!

:tu

Attachment 239978Thank you, I am still trying to figure out some of the attachments on the form at the moment I only have access to a iPhone, I hope the pictures made it and thank you again

Attachment 239979 in this photo it's a bit hard to make out the conditions I will upload a few close ups

Iphones actually take good photos, enlarge and get close with good lighting and a lite background.

Clean with 000 steel wool and WD40, polish with some 1k wet and dry with a wine cork backer going easy over the etch.

That will give you a good idea of how much will come off and then make a decision on if you can keep the etch or live with some pitting.

Thank you on the advice, I used a steel wool and the wine qourk, the e dirt and rust came, there is some spots left on the blades, I tried uploading photos it wot aloe me to,

Quote:

---

Originally Posted by LeicaRazor1

Hi, First time user of the forum,I hope I'm posting in the proper place, the etching is amazing, I would love to find a blade with anything cycling related. Yesterday I purchased 2 SR second hand, I don't have very muck knowledge on the pieces,I am afraid of losing (sanding) the hallmarks,stamps and engraving off the blades, basically I don't know where to begin, the edges feel and looks to be in shave ready (from what I can tell) any help or advice would be greatly appreciated,Best of luck on your beauty and hope everything turns out well. Thank you in advance.

---

What Brand are they? iPhones can get surprisingly good pictures.

https://m.youtube.com/watch?v=emDKR6zBOqE

https://m.youtube.com/watch?v=emDKR6zBOqE

https://m.youtube.com/watch?v=emDKR6zBOqE