-
5 Attachment(s)
Pins go in from the show side to the reverse side...
Attachment 17025
I always pin the wedge first then the middle (if applicable) and finally the pivot...
Attachment 17026
Attachment 17027
Again the pins go in on the show side..
Attachment 17028
Don't forget the bearing washers if you are using them...
Attachment 17029
-
7 Attachment(s)
Bearing washer, razor, bearing washer....
Attachment 17030
Don't mess up now, this is the end of the journey, be extra careful peening the pivot pin, if you leave this pin to long, you stand the risk of a bent pin, to short you have to make a new pin...
Attachment 17031
Attachment 17032
Attachment 17033
Attachment 17034
Attachment 17035
A completed razor, some final hand polishing on the blade, then it is ready for the hones......
Attachment 17036
-
All I have to say is wow....I'm not a huge fan of the framebacks, but you certainly did make that razor look sharp (pun intended)! Keep up the great work,
Dave
-
Thank you Glen. Thanks for the tutorial and thanks for the work you did on my razor! It looks awesome!
You just gotta love that spalted curly apple.
I hope you don't mind, I'd like to add a safety note here. Spalting is a product of the decay process. Spalted woods display those patterns because of fungus eating its way through the grain lines. The sugars in the wood react with the fungi causing the various color patterns. Once dried, the fungus becomes dormant, not dead. If the fungal spores get wet, they may very well resume growth. This can happen in the wood, or it can happen in your respiratory system. It is always wise when sanding to wear some sort of filter mask or respirator. However, when sanding spalted wood, consider it a must. There have been documented cases of severe respiratory infections due to inhalation of fungal spores while sanding spalted woods.
Brad
-
Excellent job Glen. Thanks for posting the process. :tu
-
excellent post Glen, thank you very much for sharing it with us.
best wishes,
Mark....
-
Glen, as usual, awesome job! I'd like to know a little more about how you go about doing the wipe-on poly with the inside of the scales and the wedge. Do you coat the entire inside of the scale (once or more)? Do you coat the wedge prior to installation? Do you pin the wedge end and then coat all of it as a unit?
I know I have my method, but I'm always willing to learn - and I think this could be of great use to the other neophyte restorers like myself :)
Again, your willingness to share information is a credit to you, good sir.
Mark
-
2 Attachment(s)
Glen, as usual, awesome job! I'd like to know a little more about how you go about doing the wipe-on poly with the inside of the scales and the wedge. Do you coat the entire inside of the scale (once or more)? Do you coat the wedge prior to installation? Do you pin the wedge end and then coat all of it as a unit?
First thing I do is 3 coats of finish on the inside, after that really dries, I put two pieces of double side tape on the edge of what ever mailing box is in the room at the time.... I stick the scales to the box where the wedge would go, and then start the process of doing the outside coats with a box to hang unto and the scales securely attached to it.... This is for wipe on finishes....As you can see this box gets used alot....
Attachment 17038
For spray on finishes, again I do at least 3 coats on the inside, before I get the outside started.. I made some holders for the scales for spray finishes.. Just a piece of wood and some stiff wire...
Attachment 17039
As to the wedge end ??? Yes the wedge is coated to as I do the outside, I do 3-5 coats depending on the finish I am using, this is for wood/bone wedges...
I know I have my method, but I'm always willing to learn - and I think this could be of great use to the other neophyte restorers like myself :)
Again, your willingness to share information is a credit to you, good sir.
Mark
-
Really helpful posts here. Thanks for imparting your knowledge!
-
shouldn't this be a sticky? I want to be able to find this in three years when I'm finally read to think about doing this.