Can I restore these Scales?

These are a little bit the mongrel dog...

But, any chance these might be able to be refinished / restored? I dont have the cash to spend on custom scales ATM. Plus, it would be neat to keep these...

http://farm3.static.flickr.com/2653/...642445791c.jpg

http://farm3.static.flickr.com/2636/...36d7acf569.jpg

How would you recommend I clean / refinish them?

They should refinish well. I would take some very fine grit sandpaper, preferably wet/dry automotive in the 600/800 grit range to start and use some light oil instead of water on the sandpaper. Then sand off the most haggard areas until as smooth as you'd like. Then move up to 1000 grit or 1500 if you've got it, also with oil and you should like what you've done.

That's an inexpensive way of restoring horn scales by hand.


Chris L

Quote:

---

Originally Posted by ChrisL

They should refinish well. I would take some very fine grit sandpaper, preferably wet/dry automotive in the 600/800 grit range to start and use some light oil instead of water on the sandpaper. Then sand off the most haggard areas until as smooth as you'd like. Then move up to 1000 grit or 1500 if you've got it, also with oil and you should like what you've done.

That's an inexpensive way of restoring horn scales by hand.


Chris L

---

Thanks, two questions...

1. Any specific type of oil? I have stuff for bamboo and other assorted woods. I think mineral based. Also a beeswax type oil.

2. One of the sets are cracked by the pivot pin. Any way to reinforce the crack?

Ill take pics of the cracks tonight.

1. Neatfoot oil is the preffered oil by many. But most any mineral oil should do the job.

2. If the scales are cracked, then in order to repair them you are going to have to remove the scales to fix the crack properly. There was a thread not too long ago about this very subject in the workshop. Look back a couple of pages and you should see it. I think the member used epoxy and a few color mixtures to fill in the crack.

Quote:

---

Originally Posted by sapito318

1. Neatfoot oil is the preffered oil by many. But most any mineral oil should do the job.

2. If the scales are cracked, then in order to repair them you are going to have to remove the scales to fix the crack properly. There was a thread not too long ago about this very subject in the workshop. Look back a couple of pages and you should see it. I think the member used epoxy and a few color mixtures to fill in the crack.

---

Neatsfoot +1

And if you are going to do repairs with glues, you want to work that part of the restore before you put oil on the scales...

Thanks, I forgot I do have Neetsfoot oil so I am good to go there.

Here are some pics of the crack... Its bigger than I thought, sorry the pics came out crappy...




http://farm4.static.flickr.com/3448/...675c2498ec.jpg

http://farm4.static.flickr.com/3448/...675c2498ec.jpg

http://farm4.static.flickr.com/3517/...f469ee5b32.jpg

Definitely restorable blades. Those W&B scales are really neat! I've never seen them imprinted like that.

Thanks!

I actually started a restore on the blades... read about it here.

Any type of epoxy thats recommended?
Also where can you buy tint for epoxy?

I have a lowes and home depot nearby not too much else though (that I know off). Id love to pick some up tomorrow.

From what I have read/understand, DEVCOM 5 Minute Epoxy is a good product for this sort of thing.

Heres a Link: LINK
You should be able to pick that up at Lowes or Home Depot no trouble.

Thank you very much for the link... Ill try and pick some up tomorrow!