Thanks for the look at what you are doing. Very nice.
R
Printable View
Thanks for the look at what you are doing. Very nice.
R
Saying that the wedge was a bugger is a bit of an understatement. I think that next time I will be a bit less ambitious and go with a simple spacer.
https://lh3.googleusercontent.com/_2...2019.49.10.jpg
That's 60 grit dry sandpaper on my handy dandy granite tiles.
https://lh6.googleusercontent.com/_2...2020.19.01.jpg
https://lh5.googleusercontent.com/_2...2020.22.52.jpg
Way too thick. I sanded down alot after this. I was really surprised by how thin I needed to go with the wedge, and also by how little angle you need in the wedge.... and also by how difficult it is keeping the wedge sides flat and even relative to each other.
https://lh3.googleusercontent.com/_2...2021.26.56.jpg
Test fit, with brass bolts and nuts providing temporary assembly duty. Thank you SRP wiki... at least 1 guy read it :deal:
https://lh4.googleusercontent.com/_2...2021.40.30.jpg
I didn't think I had enough things to go wrong, so I figured what the heck, lets throw another pin in there! When I went to pin it, I couldn't find the hollow rod that I had bought... back to microfasteners again. Hopefully, their shipping will still be ridiculous :soapbox:
Why yes, that's me at midnight, using a large kitchen spoon to pin scales. It shouldn't take long, there's only 5 pins and 30 washers... and I can't seem to locate my flush cut pliers, so I ended up doing a fair bit of manual filing... oh well, live and learn.
She is sanded to 12,000 grit using micromesh and a foam block. I thought that stuff would be overkill, but it really brings out the natural grain and leaves a very worn in feel to the surface. The satin finish isn't too bad and the texture and grain stand very well on their own.
My pinning sucks. I don't know what you can see in the pics, but in person it's not even remotely up to snuff. Fortunately I have plenty of rods and spacers.
https://lh4.googleusercontent.com/_2...2023.54.49.jpg
https://lh3.googleusercontent.com/_2...2023.55.08.jpg
https://lh5.googleusercontent.com/_2...2023.56.30.jpg
https://lh6.googleusercontent.com/_2...2023.55.43.jpg
https://lh5.googleusercontent.com/_2...2023.55.24.jpg
My next set of scales will be much better and incorporate the lessons learned. I'm thinking less destroyer and more cresting waters. I might have to save the water theme for my Genco Fluid Steel. The next scales will definitely be much less beef and more curvy and lithe.
I will be tearing these back down to put a proper spacer bar in the resting pin and to sand the inside of the scales to hopefully correct some closing geometry issues. I made the mistake of leaving them rough cut from the saw and the scales are closing to one side. I put a thicker washer on the tight side and a hammered washer on the gaping side and that helped a bit, but I still think the issue is that the surface it's rotating against is rough and unsquare.
I also need to coat it in tung oil. That being said, I still intend to shave with it tonight, as is.
You're doing a great job for your first attempt!
My only advice: don't abandon the wedge. The angle is your friend.
What's your reasoning for keeping the wedge?
What advantages does it offer over a simple spacer?
What's your take on the proper amount of angle in the wedge? I'm thinking the spacer needs to be perfectly square in all dimensions relative to itself and then a few passes on coarse sandpaper to give it the wedge. I'm thinking that the angle isn't drastic at all, not more than 5 or 10 degrees at most.
I'm thinking about finishing in CA glue based on the recommendation of my betters. Basically, tung oil would have to be reapplied annually.
I did rub a bit of baby oil into the finish to see what it did. It seemed to darken it a bit.
Better pics without the background clutter. Also, a pretty good book:
https://lh6.googleusercontent.com/_2...2021.06.48.jpg
https://lh4.googleusercontent.com/_2...2021.06.09.jpg
https://lh3.googleusercontent.com/_2...2021.04.07.jpg
https://lh3.googleusercontent.com/_2...2021.07.54.jpg
https://lh5.googleusercontent.com/_2...2021.10.00.jpg
I apologize for the flash. The top is a Karl Pecker 6/8ths, another beauty. The bottom is my next project. It's a W&B faux frameback.
https://lh4.googleusercontent.com/_2...2021.11.44.jpg
https://lh5.googleusercontent.com/_2...2021.11.25.jpg
I'm going with a hollow girder type look. Something along the lines of Orange County Choppers Web themed bikes. I want each of the pins to be at the center of of each web, including the ones used in the wedge. I also want to put hollows into the wedge. I'm going to use a densely grained oak for the scales. Hopefully they won't fall to pieces when I hollow them out.
I really like what you've done so far.
My only suggestion is to make the tang end of the scales narrower, so that it matches the width of the tang when the razor is opened 180 degrees (basically make a smooth transition from the tang to the scales). That makes stropping and honing easier.
Thank you. I've actually thought about thinning the scales out alot more. They are pretty close to the original 1/8ths thickness and they feel very beefy. I also still need to smooth out the inside of the scales. I'm considering making them more of an almost oval shape and tapering both the inside and outside edges of the scales.
I also drilled two different size peens in my desktop anvil. Surprisingly it completely smoothed out my peens and well rounded them and the triple washer stack. They feel right now. Peening them on the same flat anvil left the surface of the peen smooth, but the edges were rough, snaggy.
Thanks again for the feedback.