Thread: Pyramid (Scheme) Sharpening..Why it just might work

Hey guys,

I've been lurking around the straight razor forum and getting acclimated. I consider myself to be a good sharpener, and I know I like to analyze what exactly is happening when I sharpen. But sharpening my straight razor has always been a challenge for me.

I watched the video of Lynn sharpening his razor, and just as I was wondering why he would switch back and forth betwen the 4000 and 8000, he explained why, and said the edge is very "delicate" on a straight razor. That word stuck with me, and I immediately went to get my razor.

The explanation still didn't make sense to me, but as I was trying to visualize what was going on as I was sharpening, it hit me. The way stones work is by making scratches (especially Shaptons). Each successive grit level makes wider and more shallow grooves in the steel. So here's my theory on how and perhaps even why the pyramid sharpening works:

The coarser stone (whatever brand or grit) will make groves in the steel. By using that stone first, you end up with an edge that resembles peaks and valleys. The valleys are the part of the blade that you want as a finished product, but not the peaks. By then going to the finer grit, it reduces the peaks until, theoretically, they are even with the valleys from the coarser stone.

OK - this much is probably a given. However, this is where the term "delicate" started to really make sense.

If I use a Shapton stone (which I do) or any other, of any grit constantly, I would get the same version of the peaks and valleys descibed earlier from using the coarse stone, just at a different ratio. However, by making the peaks and valleys on the coarser grit (in this case, the second to last stone), and then smoothing them over with just a few passes on the finer grit (in this case, the final stone) WITHOUT establishing a new set of peaks a valleys, well... you should then have a very nice shave .

This method also seems to promote the very gradual approach to the thinnest possible edge without "going over", and removing unneccesary metal from the edge.

BTW, I used a Shapton Glass 16K and 30K. I didn't follow the pryamid per se, but I tried going between the 2 stones and I did notice a better finish on the blade than just using the 30K over and over. I didn't strop. I got a good shave, but it still wasn't quite what I am looking for, but it is definitely a step in the direction I want it to go.

I am going to take my blade back down to #2000 and work it back up using the pyramid "scheme". I think the overall edge has been rounded over too much from all the previous stroppings on the barber's strop. Unfortunately, I only shave once a week, so I will have to wait until next week to personally see if my theory is correct.

If anone is able to follow my babble, I would love to hear theories - either way. Of course if everyone else has already had this epiphany, and it was already discussed in a previous thread, I've just had it for myself.

This method also seems to promote the very gradual approach to the thinnest possible edge without "going over", and removing unnecessary metal from the edge.

This is it.Explains everything person needs.

Yeppers +1 with what Sham just said...

I always explain it like this.... "You want to sneak up on the edge"

interesting. so should I be pyramidding my 1k to 4k shapton routine? (after the 4k I go to coticule and escher so that's probably the end of the pyramidding for me).

I do find I'm doing a lot of laps on 1k and then a lot of laps on 4k - on shapton would pyramidding reduce my wear? I'd only heard it suggested for nortons before.

Code:

interesting. so should I be pyramidding my 1k to 4k shapton routine? (after the 4k I go to coticule and escher so that's probably the end of the pyramidding for me). 
 
I do find I'm doing a lot of laps on 1k and then a lot of laps on 4k - on shapton would pyramidding reduce my wear? I'd only heard it suggested for nortons before.

I was wondering the very same thing - do I need a pyramid on the lower stones, or only the final 2? I would imagine only the final 2 or 3 stones, depending on how many you use.

On the 1K you want to make sure you get a burr because after the 2K, Shapton stones won't remove enough metal to really establish a new bevel. I think the pyramiding would work more effectively on anything after about #3000 grit, which is where polishing begins. But I'm still happy about my little "discovery" right now to think too much about that .

BTW, I forgot to say 2 things in my original post - 1st. Lynn's video was very well done, very informative, and easy to follow. 2nd. I sharpen a lot of other knives, and I usually use a bit more force than what Lynn prescribed for the straight razor. I think lightening up also helps a lot to keep those unwanted grooves from forming, and gave me a better finish.

Try jointing the blade on the 30k shapton and then drawing the edge toward you very lightly 3x. You won't need to strop and the edge is awesome as a shaver.

There are many schools of thought about honing. I like to think of honing as a progressive process going from coarser to finer. Unlike yourself I haven't found that finer hones make a wider groove but instead a narrower groove as the abrasive particles are smaller (mesh size). As I move out to 8k, 16k, and 30k, the pressure on the edge gets lighter and lighter as the edge of the blade is getting thinner and thinner. I also use a side sharpening technique for that reason.

Howar

Originally Posted by Howard

Try jointing the blade on the 30k shapton and then drawing the edge toward you very lightly 3x. You won't need to strop and the edge is awesome as a shaver.

What is "jointing" the blade?

Originally Posted by Utopian

What is "jointing" the blade?

It is a very light breadknifing to remove any anomalies (microscopic) on the cutting edge. Harrelson does it on the DVD that Howard did where the side sharpening technique is demonstrated.

and what is side sharpening?

Originally Posted by loueedacat

and what is side sharpening?

It is a technique that Harrelson Stanley of Shapton USA uses for plane irons. He adapted it to straight razors in a DVD put out by Howard of The Perfect Edge. I describe my limited experience with it in this post here.