Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Junior Member HedoDiver's Avatar
    Join Date
    Mar 2007
    Location
    Hopewell, NJ
    Posts
    16
    Thanked: 0

    Default Uh oh... I over-honed

    Hi all,

    Well... this sucks.

    After remembering to NOT try to catch a dropped razor, my freshly honed straight had a tiny visual "ding" along the edge when it landed in my sink. I couldn't feel it with the thumbnail test, and didn't even see it until a few days later. Regardless, I didn't want to take any chances.

    So... onto my Norton 4K/8K for a basic pyramid (3/3, 1/3, 1/5) and then 20 strops on linen and 30 strops on leather (Tony's #1 latigo). At this point I could barely see the blemish on the blade, so I thought I was good to go.

    So... when I shaved this morning, I experienced a perfect textbook example from Lynn's video about what an over-honed blade feels like. It didn't "pull" at all, but I wasn't cutting any hair.

    I had to finish with my DE.

    Now, I'm new at both stroping and honing, but have watched Lynn's video several times and read a whole lot. I used only the weight of the blade, kept it perfectly flat, and didn't see anything obvious that I was doing wrong.

    So.... what do I do at this point? Another pyramid? Wait until I have a yellow corticule? A thumbnail test to try to strip the burr?

    God I hate being a noob.

    Thanks all!

    Peter

  2. #2
    Electric Razor Aficionado
    Join Date
    Apr 2006
    Posts
    3,396
    Thanked: 346

    Default

    If all you did was a basic pyramid then it's unlikely you overhoned. Something else went wrong. My guess is you managed to really really dull it. If this was your first time using the norton then you might want to make sure the stone is lapped flat - the first time I used the norton mine wasn't lapped flat and it dulled the razor instead of sharpening it.

  3. #3
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    This is interesting......try a couple of 1-3's, strop, test and report.....

    Thanks,

    Lynn

  4. #4
    Senior Member blabbermouth
    Join Date
    Aug 2006
    Posts
    3,063
    Thanked: 9

    Default

    Would you say you used pressure to get rid of the ding?

    One more vote for a dulled edge here, and Michael has given excellent advice on lapping the stone. Draw a grid on the hone with pencil and do a figure 8 - if this doesn't remove the grid evenly in 1-2 laps it wasn't ready for honing and dulled the edge.

    Cheers
    Ivo

  5. #5
    Senior Member Namdnas's Avatar
    Join Date
    Jan 2007
    Location
    Rhode Island, USA
    Posts
    387
    Thanked: 1

    Default

    Would someone please explain to me what 'over-honed' actually refers to?

    Another way to put it, if I sectioned the blade int he axial direction (leaving a slice like those shown on the Henkles grind guide), what would an over honed edge look like? Dull, or wide edge? Folded over wire edge? etc... thx - John

  6. #6
    Senior Member
    Join Date
    Sep 2006
    Posts
    1,180
    Thanked: 1

    Default

    Quote Originally Posted by Namdnas View Post
    Would someone please explain to me what 'over-honed' actually refers to?

    Another way to put it, if I sectioned the blade int he axial direction (leaving a slice like those shown on the Henkles grind guide), what would an over honed edge look like? Dull, or wide edge? Folded over wire edge? etc... thx - John
    John -

    If I understand the term correctly, it generally refers to a wire edge. I think its when the edge gets so thin from sharpening that it creates a thin wirey(?) burr. Certainly no expert me but this is what I've gleaned from reading.

  7. #7
    Electric Razor Aficionado
    Join Date
    Apr 2006
    Posts
    3,396
    Thanked: 346

    Default

    It doesn't have to be that far gone. It's possible for a blade to be a little bit overhoned, in which case the edge is weak and may not survive very long (couple of shaves), and tends to shave uncomfortably.

  8. #8
    Senior Member blabbermouth
    Join Date
    May 2006
    Posts
    2,516
    Thanked: 369

    Default

    Quote Originally Posted by Namdnas View Post
    Would someone please explain to me what 'over-honed' actually refers to?

    Another way to put it, if I sectioned the blade int he axial direction (leaving a slice like those shown on the Henkles grind guide), what would an over honed edge look like? Dull, or wide edge? Folded over wire edge? etc... thx - John
    Over-honed means the edge is honed to the point that it is too thin and tends to break off, or crumble as it cuts. You can detect this condition by using the thumb nail test. As you pull the blade across the nail, if the edge bites into the nail, but feels rough like a file (due to the edge crumbling), instead of feeling smooth, it is likely over-honed.

    You could test for this on your face with a shave, but me, I'd rather not do any testing on my face. The thumb is a very reliable indicator.

    I'm not sure what an over-honed edge would look like in cross section. But I do know this: once you learn how to use your thumb nail while honing, you can avoid over-honing most of the time. And if you do over shoot, you will know right away.

    Scott
    Last edited by honedright; 04-10-2007 at 06:07 PM.

  9. #9
    Member AFDavis11's Avatar
    Join Date
    May 2005
    Location
    Virginia
    Posts
    5,726
    Thanked: 1486

    Default

    Great explanations! In a microscope an overhoned edge to me starts with little stars/breaks in the edge. As the condition gets worse the edge goes from looking like a smooth "wall" to a "wall" that has had a sledgehammer taken to it. Lots of tears, holes, rips etc. It might look like an irregularly patterned serrated blade on the edge.

    You will usually be shocked when you see a badly overhoned razor and it can be easily felt with the thumbnail test. Its the slightly overhoned edge that is really hard to feel or see.

  10. #10
    Cheapskate Honer Wildtim's Avatar
    Join Date
    Nov 2006
    Location
    A2 Michigan
    Posts
    2,371
    Thanked: 241

    Default

    By the way if you can still "barely see the blemish on the blade" with the naked eye I wouldn't consider the razor "good to go" I would think it still needs quite a bit of work.

    I will usually work a nick out until I can't see it even under 60x magnification. Then I move on to sharpening the blade.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •