Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Junior Member
    Join Date
    May 2010
    Posts
    5
    Thanked: 0

    Default Repairing a strange problem with my new Robert Williams razor.

    Well I received my first razor, a modern custom Robert Williams from Ebay. The problem I noticed right off the bat was that the spine has a gentle curve but the edge is more or less straight, except for the dull tip of the edge. In other words it's hard to sharpen. The exact measurement starting from the heal are 25/32nds 21/32nds and the tip is 24/32nds. Is this from improper honing? Shouldn't the edge follow the curve of the spine? And should I hone it into cooperation? You can kind of see the problem from his website.
    customstraightrazors.com - RAZORS/#055 6/8 humpback w/ smooth polished Oryxhorn scales
    Last edited by seedomo; 05-30-2010 at 12:51 AM.

  2. #2
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    For me as long as the angle the edge makes with the stone is constant along the blade there is no problem, you just need to figure out which stroke will do the job. Try the magic marker trick and see how it goes.

    Another option is to contact Robert Williams and ask advice on honing , better yet send it to him for pro honing, if he offers the service.
    Last edited by mainaman; 05-30-2010 at 12:33 AM.
    Stefan

  3. #3
    Junior Member
    Join Date
    May 2010
    Posts
    5
    Thanked: 0

    Default Thanks

    In all honesty last night I honed and honed until I started to notice the toe edge getting wider, at least on one side. I figured it was trying to right itself based on the curve of the spine. I've attached images that might show that the blade isn't quite straight based on the uneven wear of the edge. Here's hoping I didn't screw it up beyond repair.


    That's not a chip in the blade in the middle, just a reflection.
    Last edited by seedomo; 05-30-2010 at 12:50 AM.

  4. #4
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    That really looks like more a problem with honing pressure to me.

    Have you held the blade between two straight objects? If it lays flat and the only areas where you see problems is where the metal was taken away from honing, that is what will need to be corrected. Unfortunately, there has been a lot of metal removed already.

    Lynn

  5. #5
    Junior Member
    Join Date
    May 2010
    Posts
    5
    Thanked: 0

    Default Thanks

    The edge is flat, but if I hold a straight edge from heal to toe between the spine and edge, one side shows a gap in the center and the other side rocks a tad. The side that is convex shows edge wear where I'd expect to see it, in the center. The other side is shows the opposite edge problem and is concave.
    Last edited by seedomo; 05-30-2010 at 01:12 AM.

  6. #6
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    It may be worth sending it to Robert to take a look at.

    Good luck,

    Lynn

  7. #7
    all your razor are belong to us red96ta's Avatar
    Join Date
    Sep 2009
    Location
    Fresno, CA
    Posts
    1,368
    Thanked: 446

    Default

    Dude, seriously, you're killing with the honing. Send it to Lynn for a good honing. After that, it's just two swipes on a 12k every three months.

  8. #8
    Robert Williams Custom Razors PapaBull's Avatar
    Join Date
    May 2005
    Location
    East Liverpool, Ohio
    Posts
    971
    Thanked: 324

    Default

    I'm not sure what that razor looked like when you got it because it left my shop a long time ago, but those pictures make me cringe. That razor has been virtually destroyed. I got your e-mail, called you up and got your voicemail. Did that razor look like that when you got it? That was a razor for someone that liked a humpback look but wanted a straight edge instead of a smile, so it was a bit unusual but it had a beautiful bevel on it at one time and shaved great.

    Give me a call. We'll figure something out.
    Last edited by PapaBull; 05-30-2010 at 02:18 AM.

  9. #9
    Junior Member
    Join Date
    May 2010
    Posts
    5
    Thanked: 0

    Default Thanks for the reply

    I'm plugging in my dead phone now.

  10. #10
    . Bill S's Avatar
    Join Date
    Sep 2006
    Location
    Richfield, Ohio
    Posts
    2,521
    Thanked: 597

    Default

    I would follow Lynn's advice. I'm no expert, but I think you need some serious remedial work (not you, your razor, of course ). I don't think that's going to get fixed by more honing.

    Edit: Again, I'm slow posting. ;-(
    Last edited by Bill S; 05-30-2010 at 02:21 AM.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •