Thread: Some help with my technique please

Gentleman,

I am having a bit of trouble getting a smooth shave with the Griffon Carbmagnetic XX I picked up from Lynn. I have been using a safety razor (Merkur Futur) for some time and get excellent shaves with that. I am not sure what the deal is with the straight but I experience a lot of drag with the blade. With the Futur I am very used to paying close attention to the angle and do the same with the straight. I have tried several angles on my face an none seem to make the razor cut any smoother.While I have been lucky enough to not spill any blood, I have recieved the worst case of razor burn on my lower cheeks and jaw line all three times I have used it. I am using one of the four sided paddle strops made by Tony by the way.

Here is my routine:

Hot shower (I usually apply a little conditioner to my neck at this point)
Soak badger brush and work up a lather (Truefitt and Hill)
Apply lather to my face and let sit
Strop 30-40 round trips
Apply hot towel
Reapply warm lather
shave
Truefitt and Hill aftershave.


Any tips on what I can do to get a closer shave without drag and razor burn? I have watched Lynn's video and read the help files.

Thanks for any input.

Hi JBahn,

Your beard prep appears to be o.k. What kind of strop do you have and how many laps are you putting on the razor before you shave? If you strop wrong (e.g. too much pressure or failure to keep razor flat to the strop) you can dull the edge. Another factor can be blade angle to the face. The razor should be one to two spine widths away from the face, maybe more or maybe less depending on your face and what area you're shaving. Another factor can be failing to stretch the skin tight enough. Usually it's one or more of those things that results in a poor shave.

Ed

If you're getting burn then it's the pressure. Or the stropping, but it sounds like you're stropping enough, so it's probably the pressure. Used properly, straights are much easier on the skin than even a DE. Back when I was experimenting with the feather and my skin got so thin it would start bleeding if I rubbed it, I could still shave with a straight without incident.

I think stropping may be the issue. With the paddle is seems difficult to strop effectively without putting pressure on the blade.

Will a strop work just as well if you run the razor on it slow?

I was thinking of picking up a hanging strop as it seems that might be easier to keep the blade in contact with too much pressure.

Also, should every razor be able to pass the HHT? I never could get this one to do it.

No, not every razor passes the HHT. I never could get a Feather blade to pass it, and those blades are by far the sharpest thing I've ever seen. My own blades I hone till they will pop the hairs on my arm if I hold the blade about 1/8 inch off my arm. However, the real test is how it shaves.

It is also possible that you've dulled the edge with the strop (I ruined my first edge that way).

Well, if the blade was sharpened by Lynn you know that the fault lies with your technique.

Remember that Rome was not built in a day and learning straight shaving takes much practice and patience. Facility with the razor will come with use and the few things you need to remember have already been said. Just remember to become comfortable with holding the razor in different positions and then watch your blade angle and keep the skin stretched and use no pressure on the blade. Let the blade do all the work. I think most here will tell you that when they started they suffered irritation for some time.

Some pick up the skill fast and more easily and some more slowly with more pain but everyone picks it up. Remember ,at one time everybody shaved this way so if they could master it a hundred years ago so can you.

I'm guessing you know about the 20 to 30 degree angle (spine to face ratio) and about pulling your skin tight, making the whiskers stand up better.

The first key thing that stuck out to me was the paddle strop. the 2nd was the "putting pressure on it. My guess is you've possibly dulled the blade a bit by putting too much pressure onto the blade.

Before you decide you've done that I would suggest getting or making a hanging strop. Do you have a wide belt that's at least 2 inches wide and has a smooth finish? if not go to a local shoe repair shop and ask if they've got any thick smooth leather you can use to make a strop. ask for a piece that's around 3 inches wide by 26 to 36 inches long. put a couple grommets in the top and run a shoe string through it. This will run you about 4 to 8 bucks total and will do until you can get a nice hanging strop. If you've got the belt that will work too.

soften the leather with armor all or lexol or something similar. hook it onto a door knob or something and pull it tight. try about 40 to 60 rounds with almost no extra pressure on the blade. If it still shaves badly then hone it or send it back to Lynn for another honing. He's pretty good about that stuff.

Also, some blades need to be restropped between "passes" I'm assuming you know that passes means to shave the whole face with the grain the first time then the 2nd pass is shaving either cross grain or against the grain.