6 Attachment(s)
5/8 Imperial Razor in Purple Heart
So, this was one of three blades that I purchased on Ebay, each for under 12 dollars (this was my goal). It is an Imperial Razor, a definite 5/8 to the top of the hollow, hollow ground, with "Registered 20507" on the tang. The blade had been finished once before, I found out as I was sanding it down: close to the bevel, I could see what appeared to be the bottom two bicycle wheels. After further research, I have discovered that those are actually the wheels of a 1900's Model Ford, and the engraving had been long gone before I started working. What little I can find on this blade indicates that it dates between 1900 and 1938; however, most of the "car" Imperials are New York-Germany marked whereas this is simply marked with Germany.
I didn't take it to a mirror finish, so you can still see some of the work marks on the blade. (To be honest, looking at it, and the pictures, the pictures catch the light and make them look far worse than they are...meh). The scales are purple heart with a CA finish and the wedge is black horn. The pins are Ni-Ag with brass washers from microfasteners, and the "bearing" washers on the hinge pin are flattened and polished brass washers of the same type. On a side note, I think Dante forgot to mention the special level of hell reserved for trying to polish those damn little washers. I will address that later. This razor was only my third de-pinning and after my attempts broke the scales of the first two, I bought some flush cutters and de-pinned this one successfully. The vulcanized rubber/bakelite scales are still serviceable, if needing a little love, but I have re-scaled the blade anyway (the bakelite scales will be restored and then stored away for later projects). I thought that a more square-themed scale pattern would better balance the profile of the blade; and some colorful wooden scales would class-up the entire assembly.
Before:
Attachment 137800
Attachment 137801
After:
Attachment 137802Attachment 137803Attachment 137804Attachment 137805
As with any project, there was much learning with this one, most notably with the scales. I learned that CA can be rather finicky, and if you are not careful, it is very easy to sand through the finish or get drips, or runs, or these wierd ribbon-stalagtite-formations. After much trial and error, though, I got a pristine glass-like finish on the scales. I was proud. Then I tried to shape the wedge. So two things here: 1) the thickness of the CA did create slightly rounded edges, which meant the wedge did not fit flush, and despite my efforts to sand down the area in which the wedge would be affixed, the un-flush-ness remained 2) sanding down the wedge to shape blemished the CA finish. On the razor, you can see that the wedge end lost some of its CA luster. The latter can be solved by shaping/fitting the wedge BEFORE applying the CA, but any tips on the first conundrum?
My next question(s?) for the more experienced types. Pins and washers. First of all, I cannot figure out how you get the nice, perfectly round peans on the pin. I'm still new at this, and I am sure I will gain finesse with experience, but my pin heads always end up just slightly lopsided. Functional, but lopsided. Second, how do ya'll polish the washers and pins. This time, I polished the washers before I pinned up the razor. This was an exercise in extreme patience that rivalled dealing with my 2 year old. However, it worked, and once I pinned up the razor, all I had to worry about was sanding/polishing the pins. This presented its own difficulty, as placing the sand paper on a flat surface rendered flat, not domed, pins; and holding the sandpaper and working on the pins/washers inevitably marred the surface of the CA finish...which I then had to go back and re-polish, hoping that I didn't mar the finish as bad as I did with the wedge, and lose the luster. Anyway, looking for advice on any of those steps! Thanks in advance!
