Results 1 to 10 of 14
Thread: How to hold razor level
Hybrid View
-
09-13-2017, 05:19 AM #1
- Join Date
- Sep 2010
- Location
- Calgary, Alberta
- Posts
- 160
Thanked: 2How to hold razor level
I am looking for advice on lhoning a razor. I can get an edge that shaves, but not good. I am using Norton 1k, 4/8K hones. I am using lighter pressure which I think is helping. I think the problem is not holding the razor level enough when making passes. Would like to suggestions on how to improve this. How do you hold razor, strokes, etc. I have 2 razors with a slight smile (1or 2 mm)
How much should I expect from an 8K Norton?
JoeLast edited by binder; 09-13-2017 at 05:53 AM.
-
09-13-2017, 07:06 AM #2
- Join Date
- Dec 2012
- Location
- Egham, a little town just outside London.
- Posts
- 3,741
- Blog Entries
- 2
Thanked: 1077Hey Joe,
If you haven't already check out the honing section of the library Category:Honing - Shave Library
Lynn and gssixgun's videos on YouTube are also a great help.
Whilst honing its often mentioned to keep your elbow up to help keep your razor flat on the hone, also some slight torque of the edge helps with contact.
With a slight smile a 45° angle heel forward X stroke should do the trick, a J stroke also works well (gssixgun explains very well in one of his vids) anything more than a smirk will require a rolling X stroke.
Ink your bevels to see if your making contact with your strokes and invest in a cheap loupe, they really help to see where you are at.
The Norton 8k is considered by many to be all that is needed to have a great shave, yes higher grit hone and naturals are nice but not necessarily needed.
Above all time and patience is the order of the day. Have fun.
-
The Following User Says Thank You to markbignosekelly For This Useful Post:
binder (09-15-2017)
-
09-13-2017, 08:58 AM #3
I'm not a honing expert. One thing I picked up from Lynn, is to elevate your elbow. It made a huge difference for me.
-
The Following User Says Thank You to Wayne1963 For This Useful Post:
binder (09-15-2017)
-
09-13-2017, 06:35 PM #4
- Join Date
- Jan 2017
- Location
- PDX
- Posts
- 156
Thanked: 9I struggle with controlling the blade on the hone as well. Lifting the elbow is great advice. I sometimes use my off-hand just to keep the tip of the razor in control, applying no pressure other than to keep it on the hone. It takes some time to build muscle memory so keep practicing, a little each day will help greatly. I try and spend 15 minutes a day on the hones and have several razors in different stages, some that will need to go back on the same hone to finish that stage. The more you practice (properly) the more natural good technique will feel.
-
The Following User Says Thank You to blzrfn For This Useful Post:
binder (09-15-2017)
-
09-13-2017, 07:35 PM #5
Keep at it. Elbow up and a second hand helped me. No pressure with the second hand but as a guide. My hands are shakey so if i want to keep the blade in contact with the stone i have to use two. Its taken me about 5 months to put out a decent edge with synthetic stones but i can only hone one day a week.
Follow what the others have said and take your time. It takes a while for it to all click. Good luck and like shaving, take your time. It dont just fall in your lap. Knowing what your feeling when honing and knowing 100% that the bevel is set on the 1k is key. If you dont get that then there is no need to go further. A loupe will help with this but it just takes time.Last edited by Gasman; 09-13-2017 at 07:42 PM.
It's just Sharpening, right?
Jerry...
-
The Following User Says Thank You to Gasman For This Useful Post:
binder (09-15-2017)
-
09-16-2017, 04:34 AM #6
- Join Date
- Sep 2010
- Location
- Calgary, Alberta
- Posts
- 160
Thanked: 2Can someone explain what a J stroke is. I watched a lot of gssixgun's videos, but I don't remember that?
How many stokes would be enough for the 4K and 8K? I thought I would keep doing a few rounds from 1k to 8k until I get there. I thought I had the bevel set and did about 40 passes on the 4K and 8k but wasn't enough.
Joe