Results 1 to 10 of 10
Hybrid View
-
07-10-2019, 12:37 PM #1
Could you take a look on my honing tecnique
Good morning Gents
I am attaching for your consideration a short video of my honing technique so you can tell me what is wrong and how can be improve, I must say this is my second attempt and the video show just the last passes with clean water over a small coticule using dilucote process.
I know is too much to ask for a first timer but I am using the resource that I have at hand.
The razor is a Rudolf Schmitd Bambola 205 and the hone is a Belgium coticule/BBW after many passes over a heavy slurry I started to add water thirty passes each time, diluting and more thirty passes until clean water and no pressure on the blade.
I achieved a decent edge enough to cut arm hair effortlessly, I do not have any experience (not even seen one in person) with a shave ready razor to compare with all I have is the humongous amount of information provided by this community and some imagination to try to implement it.
Please let me know what do you see and think
https://youtu.be/0_HEz-F8IUcWish you health to enjoy your shaves
-
07-10-2019, 01:52 PM #2
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,401
Thanked: 4822A couple of thoughts.
It is quite typical that when people are new to honing razors, they tend to put way too much pressure on the spine and cause the spine to wear far too quickly. It is easily mitigated with the use of tap.
A coticule is an extremely difficult place to start compare to synthetics.
Due to you location getting together with another may be difficult.
If you watch gssixgun videos you will see how you can hold the blade so you are torquing the edge down. The finger placement seems like you may be pushing down on the blade and not concentrating on the edge.
Good luckIt's not what you know, it's who you take fishing!
-
07-10-2019, 02:06 PM #3
Thanks for the comment RezDog in my mix of information I am afraid of put too much pressure on the spine and cause more wear than it already has due to the fact that the razor belongs to a barber who used on daly basis as a work tool, although I used my both hands to control the strokes and add some pressure in the first stages with the heavy slurry since is a coticule I am guessing some pressure must be applied in order to obtain results since is a fine grit sort of speak, I was thinking in use some tape but doing that I will be adding more variables to watch after
Wish you health to enjoy your shaves
-
07-10-2019, 02:33 PM #4
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,401
Thanked: 4822If you always use the same tape, there are no added variables.
It's not what you know, it's who you take fishing!
-
07-10-2019, 02:47 PM #5
-
07-10-2019, 02:55 PM #6
Yes, use tape, always use tape. Unless you want to use tape at the very end to make a microbevel. This is done by some coti users. I cant help you with a Coti as i found them to not give a keen enough edge. So i sold mine. Had no need for a stone that couldnt give an edge I liked. It is a hard stone to learn on. In my opinion about any other stone would be better, but you are limited to what you can find. Synthetic stones are the best to learn on. Maybe one of the Coti users will chime in and help.
It's just Sharpening, right?
Jerry...
-
07-10-2019, 02:57 PM #7
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,401
Thanked: 4822It changes the angle very very little and once you have honed with tape if you choose to hone with no tape it tapes only a few strokes to change it back to the no tape angle. Super fast, super easy. It does take a while to hone well enough the tape no tape issue to be a non issue.
It's not what you know, it's who you take fishing!