Results 1 to 10 of 10
Thread: Clarification re Thumb Pad Test
Hybrid View
-
08-02-2009, 03:51 AM #1
- Join Date
- Mar 2009
- Posts
- 254
Thanked: 45Clarification re Thumb Pad Test
Even after looking at the wiki I'm not sure what direction I move the thumb when doing the TPT, or what amount of pressure to apply.
1. If the toe of the razor is north, and the heel is south: am I moving my thumb north-south or east-west?
2. With the understanding that I am not mashing down, or anything close to it: is it just a light brush across or do I add a bit of pressure? If the latter, does the pressure increase during the movement or remain the same.
I see HHT vids, but since the TPT is supposed to be more useful, it'd be helpful to see a TPT vid or two.
-
08-02-2009, 03:56 AM #2
Here is a honing vid where you can see Lynn test the edge with his thumb from time to time.
When I was getting into it Randydance advised me to take a DE or SE blade, a new sharp one, and practice with that so I would know what sharp is supposed to feel like.
I hold the spine in one hand with the heel down and the point up. I touch my thumb to the edge lightly and kind of scuff it to feel it is 'sticky'. If it isn't sharp you pad will king of slide right along. I work from the heel up to the point.
Not enough pressure to cut yourself but enough to either grab or slide.Be careful how you treat people on your way up, you may meet them again on your way back down.
-
08-02-2009, 04:06 AM #3
- Join Date
- Mar 2009
- Posts
- 254
Thanked: 45
-
08-02-2009, 04:33 AM #4
- Join Date
- Apr 2009
- Location
- Monmouth, OR - USA
- Posts
- 1,163
Thanked: 317To answer directly, if the toe is north, and the heal is south, you would hold the razor edge-up in your right hand, and move your left thumb across the edge from east to west.
If you tried to move north/south you would slice your thumb open.
I should add, that this should be done with no pressure at all. The razor edge is easily damaged, and so is your thumb. You just want to barely skim the edge with your thumb.
You can repeat the process at various points along the blade to check that the edge is uniformLast edited by VeeDubb65; 08-02-2009 at 04:38 AM.
-
08-02-2009, 05:37 AM #5
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 26,984
- Blog Entries
- 1
Thanked: 13234This is a hard technique to describe, it is even hard to do on video...
The best way to learn it is exactly what Jimmy and Randy said test a SE or DE razor to get the feel down...
I hold the razor in one hand blade up an down and kinda bounce the pad of my thumb off of the edge as I walk it down the edge from toe to heel...
You will feel the edge stick as it cuts into the top layer of skin....This is the object of this test no matter how you accomplish it....Some people just press the pad of their thumb onto the blade edge and test by how it feels as it digs in...
OK for real here, if you are not smart enough to do this without cutting yer thumb, you might really want to reconsider putting 3 inches of the sharpest steel known to man against your throat and Carotid arteries....
-
The Following User Says Thank You to gssixgun For This Useful Post:
bassguy (08-02-2009)
-
08-02-2009, 06:02 AM #6
- Join Date
- May 2005
- Location
- Saint Paul, Minnesota, United States
- Posts
- 7,974
- Blog Entries
- 1
Thanked: 2204I started by going west-east ( left to right) then I got bolder and started going south-north (heel to toe) very gently. The movement of the thumb resembles a "u", a very short gentle movement. The key point is to be consistent in performing the test. Eventually you will notice the changes more and more.
Hope this helps,Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin