Printable View
In the world of straight razor shaving DVD Lynn mentions that on a Damascus razor, you should put electrical tape on the spine to prevent the spine from being worn down from the honing.
My question is, should this be done on any razor that is honed in order to prevent its spine from being ground down?
Thank you.
OHhhhhhh boy sitting back to watch the show :popcorn:
Talk about a
:deadhorse:
:rofl2:
I think what Glen's trying to convey is that this topic may have been debated once or twice before. If I may:
It basically all comes down to personal preference. Some do tape, some don't. I do, but only certain times, like if I'm honing a wedge. If I'm honing a full hollow on, say, a coticule (which doesn't exhibit much hone wear relative to other stones), then no I won't tape...
edit: once you tape a razor though, you'll always want to continue to tape it, otherwise you'll create a double bevel...
No show to watch for me anyway. It is relatively simple from my POV, you don't want hone wear you tape it, you don't care then don't tape it.
Bob
Quote:
Originally Posted by gssixgun
Well in this case the OP is saddling a new pony of his own choice. Your own exhaustive research in this are should be an ENORMOUS sticky which comes attached to all members with fewer than 500 posts.:roflmao
Gugi should be able to install that feature in a few seconds.
Just starting out, not trying to start a fire storm :D
I really appreciate the insight about sticking to tape once you use it if you choose to.
Thank you all for the replies.
Actually the Tape issue has changed to more of a slow smolder over the last year or so, it used to be much worse,, almost like debating Politics and Religion mixed with 2nd Amendment rights all rolled together :)
Perhaps we should up the ante by bringing in the various tape factors?
Electric tape? gaffers tape? Scotch vs 3M (or are they the same these days?) Rubber vs Vinyl?
Breath no life into the dead horse! =P
Don't forget multiple layers or not .Quote:
Originally Posted by Magpie
Hey Swan,
You can search a find a lot of posts on the subject of taping. When it comes up from time to time we kinda find it hard not to have a little fun with the subject. Nothing personal and not trying to make light of your question, it's a valid question.
I'm a taper. I tape everything because I try to buy razors with little hone wear, or even NOS and then I try to keep them that way. As you recognized, it's a preference thing.
I think it is good idea for a new honer to tape until they have basically become proficient in honing. By taping you prevent uneven wear on the spine which can really cause some grief once there. After you get honing down, then decide if you want to continue taping or not. If you decide to not use it, it's an easy bevel set to get the edge in line with the spine again.
Enjoy, and have fun!! :gl:
Regards,
Howard :D
a matter of personal preference.Quote:
Originally Posted by Swan
You forgot to mention, "..while posted in the Ladies Section." :rofl2:Quote:
Originally Posted by gssixgun
Just remember that IF you choose to add tape to the spine while honing, ensure you keep a close eye on the tape. Once the tape starts to wear, you'll want to replace it immediately. This is especially an issue on lower grit hones that will chew through your tape faster.
I'll only use tape when resetting a bevel on an old razor, then I wind up taking it off and honing through my normal progression (even when resetting a bevel I won't always use tape). It just depends if there are small nicks in the edge or not and how much metal I need to remove. I use the tape to prevent more wear than necessary in cases like that. Other than that, the only time I'd use tape is if the spine had a design on it or a gold wash or something.
No tape and I don't like condoms either.
What do you mean by gold wash? Is that the gold I see on the blade on some of the more expensive straight razors or it is a decoration on the spine?Quote:
Originally Posted by MuskieMan33
Thanks