Printable View
Does anyone know where one can buy a display case that is well ventilated and hold atleast 10 straights? I need something that I can keep in my bathroom that will organize my shavers in an attractive and convienient way. Any ideas guys??? Thanks! :confused:
I may be over protective, but my razor of the day and strop only come into the bathroom for stropping and leave until after my shower. It seems to me if you have to keep them there you would want a sealed container with something to absorb moisture and control humidity. You might find a small kitchen or bathroom cabinet with glass doors at the big box stores, or a local cabinet shop. A golden rod like they use in gun safes may give you the protection you need.
I have lots of windows on my bathroom. Usually stays pretty dry in there. I always dry off my razors thoroughly after using them. I never really considered the possibility of my razors getting seriously damaged in this environment. Perhaps I should be equally cautious as you.
I use my grandmothers old spoon display case just outside the bathroom. Holds 10 blades and has cubbies for soaps and such...
Amazing...Quite crafty. Guess if I can't find a finished product I'll have to use a little ingenuity as well. What do you think about using this? I found it on eBay for $7 so far. I could make use of the shelve to hold my shave soap and mug/ badger brush.... Just need to figure out a way to hang the razors.
http://cgi.ebay.com/Spoon-Display-Ra...item27b3aaf3f9
I like the way you think. Thanks for the idea.Quote:
Originally Posted by DwarvenChef
A few of us have made display cases in various ways.You don't want it ventilated,however.You want it to seal out as much moisture as possible if it's going to be in the bathroom.I adapted a pin display case and I keep this in the bathroom but I also oil my blades to be safe.No problems for over a year.This is the vendor:
Pin Display Case
Beautiful work!
well done, nice display case!
@komjong:
Thiers Issard has beautiful display cases for 7 or 28 razors.
Very expensive- but very nice!
If you like do get a link, please send me a message.
Regards
Tom
Awesome! I like it.Quote:
Originally Posted by aroliver59
Very nice!
I've managed to find something I can use as a display case for some of the razors I keep in my rotation. This case was originally used to collect stamps but accommodates my razors wonderfully. Can actually hold up to 21 razors for three week rotation. Found it on eBay for about $30. I say a little bit of ingenuity with whatever one finds about goes a long way and can save you a bundle since some straight razor cases I've seen can be quite expensive. Keep your eyes open for what you can use.
nice collection! congrats
looks cool, nice find. i love your razorsQuote:
Originally Posted by komjong
Thanks for this thread gents, this helped me get some great ideas. I ended up googling around for shadow boxes, display case, display with hinge, etc - I eventually settled on a case that normally holds medals and picked up this:
military medal Display Case, American military medal Display Case, Wooden military medal Display Case, Memorial military medal Case
I only have two straight razors, so it does the trick.
I just use a wooden test tube holder, and an antique pipe rack that is on the wall.
That is a bitchin' idea, I love it!Quote:
Originally Posted by Wintchase
Sorry for the cross-posting, but I just now saw this thread.
My wife had this beautiful case waiting for me under the tree this morning. It is sold as a fountain pen case, but it works very well for razors and has a much smaller footprint than some of the larger flat cases. I'd recommend keeping it on your dresser or valet, rather than the moist confines of the bath.
Here's a link:
Amazon.com: Pen Box 26 Fountain Pens Writing Instruments Case Matte Burlwood Finish with Window: Watches
And pics...Attachment 85818Attachment 85819
Happy collecting and displaying!
hi, if you have a look at my display case it might give you an idea, its in the (custom& restore forum) titled mahogany razor cabinet). hope this helpsQuote:
Originally Posted by komjong
I just put one together with pieces from Michael's. It will hold my top 7 straights, my top safety razor and includes a box for blades.
Attachment 104261
The glass top displays are beautiful, but I did this on the cheap.
Attachment 104242
A piece of 1x6 oak, a table saw with a dado blade and some wood glue.
For a woodworker, this can be made any size, little rare earth magnets in the top frame hold about 20 razors in this one.:
Here is a link to a full showing of the case and a plan for the frame.
It is demountable from the wall as shown in the photo album.
Link Here
http://i195.photobucket.com/albums/z...ase/pc14sm.jpg
http://i195.photobucket.com/albums/z...aseSection.jpg
~Richard
I like this. Looking at the pin cases for a large razor collection, I think the case they call LargeQuote:
Originally Posted by aroliver59
Large Pin/Medal Display Case
Makes the most sense. The interior width of 15" allows for two columns. And with the 24" high you could have 20 rows.
What did you do for the hooks? Did you bend finishing nails in the vise?
I would think those multiple spoon racks would work if you hung them upside down and you stored the razors tang down inserted in the spoon slots. Like DwarenChef did with his Grandmothers spoon rack.Quote:
Originally Posted by komjong
Just made a small display case out of a small front loading shadow box, some square bent screw on hooks and some glue. Like how it came out and could always make a bigger one later.
Attachment 156555
I did buy some of the display cases that I mentioned in my post a few above this. After I bought them I found that they were a lot cheaper if one buys through Amazon.
See: Amazon.com - LARGE Pin Display Case Shadow Box Flag Display Case, with Glass Door, PC04-CH -
For hooks I did a bit of experimenting. I found the best to be 1-1/2" x 17 wire brads. I bought them from Lowes. I used a vise and hammer to bend them one by one.
I know this is an old post but I had an idea and am making a case for my straights out of a cigar display case. Most have a hygrometer and humidity blocks to monitor and to display the level of humidity, which I thought would be great for keeping my razors clean and dry. I am going to use a soft foam and cut out a spot for each razor to sit in snugly so they can't slide around and are secure. Hopefully this will help with some ideas.
You have a very good idea and some members swear by that type of case! Please be aware that foam can hold humidity and may cause a problem later. A solid wood or non-absorbant foam is best..in my opinion. I had a couple old horn scaled razors in a foam and fabric backed case and the scales changed dimension badly. It will take a couple months to get them equal again.Quote:
Originally Posted by Ecfrost
YMMV
~Richard
Ok thanks for the heads up. I have some synthetic foam stuff that looks like it will not absorb water. I will look into maybe using something different.
I know this is an old post but it sure is a neat item, I am going to get one as a present. Plus for the new folks on here it might be something they would be interested in. I am going to get mine in cherry. I just ordered mine.Quote:
Originally Posted by aroliver59
I will have to do something like this but arange it so they are showing more. Very nice and thanks for the ideas to all.Quote:
Originally Posted by coloshaver
I plan on having my blades open so you can see them, I am going to put my good 6/8ths Bengalls and a couple of nice 6/8ths Clauss razors I have in it. To hold them I will use thick staples, straighten one end out and stick in the backing while the other end is at 90 degrees will hold the razor in place. I plan on using some foam on the edges and have the display case in the bathroom. If I want to use one I have it right there. Plus it will be easy to rotate razors if I want too. I may get another one for the hallway.
If any of those staples will be in contact with steel be sure to use something to insulate them, a bit of heat shrink tubing or something, otherwise over time your razors will begin to rust where they touch the staples. Carbon or stainless, only difference is how long it takes. :)Quote:
Originally Posted by THORandODIN
This is my display, storage case. The two on top are my current users so I don't have to keep opening and closing the door. It fits ten but I only have seven. Plus I like that it is mirror backed. I picked it up for 15 dollars so very inexpensive.Attachment 265395
I like that Toroblanco, where did you find it?
I found it at a miniature show. They had the best prices and variety, but if you look up
vintage brass curio cabinet and be patient and you will find one you like at a good price.
Kind of like vintage straight razors and sharpening stones. I have also found them in antique stores. But the miniature show had the best prices and variety. Hope this helps.
