Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Senior Member cahnwulf's Avatar
    Join Date
    Jun 2013
    Location
    NRH, TX
    Posts
    124
    Thanked: 23

    Default Deal or no deal? $15 Griffon

    Hey Folks!

    So i'm thumbing through the classifieds and found someone looking to get rid of some "junk". In the list there was a Griffon XX straight razor and she wanted $15.00 for it. Naturally I inquired to see if she could send me a picture. The blade doesn't look too bad - some spine wear and rust stains - but the rust looks to be semi-active.

    What do y'all think - is it worth the $15 and 30 minute drive to go and get it? I've attached a pic below.

    Name:  DSC_0855.jpg
Views: 363
Size:  27.5 KB

  2. #2
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Hard to say for sure from the pic but the rust looks to be superficial, none at the edge. If there are no cracks metal polish on a paper towel will probably clean it up enough to where I would hone it and use it. YMMV.

  3. The Following User Says Thank You to JimmyHAD For This Useful Post:

    cahnwulf (06-26-2013)

  4. #3
    Senior Member Walt's Avatar
    Join Date
    Jul 2008
    Location
    Knoxville, TN
    Posts
    874
    Thanked: 312

    Default

    As the old boy sez, "It ain't much fer purty, but it's hell for stout." Griffon put out a very good quality razor and it should make you a good shaver. Fifteen bucks is a good price for a razor you will probably have to invest some time cleaning it up and having it honed. Factor in your time and gas and you will have to decide how those affect your bottom line.

    Regards - Walt

  5. The Following User Says Thank You to Walt For This Useful Post:

    cahnwulf (06-26-2013)

  6. #4
    Senior Member cahnwulf's Avatar
    Join Date
    Jun 2013
    Location
    NRH, TX
    Posts
    124
    Thanked: 23

    Default

    Provided there aren't any cracks - I think it will be well worth it. It will give me my first experience in restoration and I'm going to take my sweet time with it. Thank you both for your insight on this and when I'm finished with the resto - I'll post some pictures back up here on the board.

    Thanks gentlemen!

  7. #5
    Senior Member cahnwulf's Avatar
    Join Date
    Jun 2013
    Location
    NRH, TX
    Posts
    124
    Thanked: 23

    Default

    Yesterday I met up witht he folks that were selling the $15 Griffon. After seeing that there weren't any cracks, I decided to buy it. I got it home and tried to dig some history out of it. Not much available on the internet - all I found was that this was a pre-1940's razor. But I took some better pictures of it and wanted everyone's opinion. There is a very small amount of toe and heel wear.

    Its a 5/8 full hollow blade. I've read on here that restoring a full hollow isn't all that easy being that there isn't much metal left on the blade to sand off. The scales aren't too bad - they look like bakelite and have a small nick just above the pivot, but it does show some tarnish spots on the scales.

    Name:  photo1.jpg
Views: 287
Size:  30.2 KB

    Name:  photo2.jpg
Views: 234
Size:  33.3 KB

    Name:  photo3.jpg
Views: 251
Size:  34.9 KB

    Name:  photo4.jpg
Views: 229
Size:  31.3 KB

    Name:  photo5.jpg
Views: 258
Size:  31.4 KB
    Last edited by cahnwulf; 07-01-2013 at 12:32 PM.

  8. #6
    Senior Member UKRob's Avatar
    Join Date
    Feb 2012
    Location
    West Midlands, UK
    Posts
    1,263
    Thanked: 360

    Default

    Where did you get the comment about restoring a 5/8" from? There doesn't seem to be anything wrong with that razor as it stands - you could get ih honed and use it. If you want to get some wet and dry paper and take some of the scratches out there still plenty of metal left for you to go at.

  9. #7
    Senior Member cahnwulf's Avatar
    Join Date
    Jun 2013
    Location
    NRH, TX
    Posts
    124
    Thanked: 23

    Default

    I didn't read that it was too difficult to sand on a 5/8. Just that its not so easy doing it on a blade with a full hollow grind.

    On pics 1-3, the large black mark towards the heel is raised, so that couldn't be tarnish. Maybe inactive rust or just some dirt - though it wasn't coming off with the scrape of a thumbnail.

  10. #8
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,250
    Thanked: 3221

    Default

    Your razor looks to be in fair decent condition. If you are worried about taking too much metal off by sanding, try OOOO steel wool with some metal polish. Give her a good going over and you may be surprised.

    Bob
    Life is a terminal illness in the end

  11. The Following User Says Thank You to BobH For This Useful Post:

    cahnwulf (07-01-2013)

  12. #9
    Senior Member cahnwulf's Avatar
    Join Date
    Jun 2013
    Location
    NRH, TX
    Posts
    124
    Thanked: 23

    Default

    Looks like I'll be making a trip to Walmart on my way home today. Is there a metal polish that you would recommend?

  13. #10
    Senior Member Walt's Avatar
    Join Date
    Jul 2008
    Location
    Knoxville, TN
    Posts
    874
    Thanked: 312

    Default

    You only have to worry about a full hollow blade if there is very deep pitting. Your razor doesn't fit into that catagory. While at Walmat pick up some wet/dry sandpaper in the auto section. They sometimes stock a combination pack with a variety of grits. Make sure you get 2000 grit for a final sanding. Any metal polish will do. Maas is good, but Meguires or any other name brand will do.

    Regards - Walt

  14. The Following User Says Thank You to Walt For This Useful Post:

    cahnwulf (07-01-2013)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •