Search:
Type: Posts; User: coachschaller; Keyword(s):
Search: Search took 0.01 seconds.
-
09-19-2019, 08:44 PM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
All fitted up ...
All fitted up
https://sharprazorpalace.com/members/coachschaller-albums-moose-brush-picture311319-brush-full.jpg
and the bottom
... -
09-19-2019, 10:56 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
yes!!!! In one of the brushes I did a test...
yes!!!!
In one of the brushes I did a test fit of the bottom magnet and it got stuck - but it was turned the wrong way. I also had already glued the magnet to the knot. I had to take a small... -
09-19-2019, 10:38 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
More progress Getting ready to epoxy it in. I...
More progress
Getting ready to epoxy it in. I used two part marine epoxy.
https://sharprazorpalace.com/members/coachschaller-albums-moose-brush-picture311313-20190918-181145.jpg
mixed up and... -
09-19-2019, 10:34 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
I will have the bottom magnet sealed and if the...
I will have the bottom magnet sealed and if the coating does not prevent the rust on the brush I can easily seal it as well
-
09-18-2019, 01:52 PM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
Here is a group shot of three ...
Here is a group shot of three
https://sharprazorpalace.com/members/coachschaller-albums-moose-brush-picture311273-20190914-121046.jpg
The bottom drilled out for a rare-earth magnet
... -
09-18-2019, 11:32 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
Still doing the finishing touches on number 1. I...
Still doing the finishing touches on number 1. I have had a couple of test shaves so far and had to drill a little deeper. The knot was splaying too much for my liking. Not sure I like the knot -...
-
09-14-2019, 11:40 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
Hoping to get started today. Going to a friend's...
Hoping to get started today. Going to a friend's place. I have a trick or two up my sleeve for this project :o
My biggest decision is how to finish the bottom: I might cap it with a piece of... -
08-30-2019, 04:53 PM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
Thanks a ton! what is a v block?
Thanks a ton! what is a v block?
-
08-30-2019, 04:52 PM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
Do you tape the sides? Or are you taping the...
Do you tape the sides? Or are you taping the bottom with leaving the center (porous) part to absorb the CA? I plan on sealing both the bottom and the inside where the know will go.
I might do a... -
08-30-2019, 11:32 AM
Thread: How deep to drill?
by coachschaller- Replies
- 22
- Views
- 7,444
How deep to drill?
Looking at finally making a brush from moose antler that I bought. I will be initially using a 26mm mixed boar/badger from Maggard's as the knot. How far down should I initially drill for the knot....
Results 1 to 10 of 10