Search:
Type: Posts; User: BobH; Keyword(s):
Search: Search took 0.14 seconds.
-
11-04-2015, 02:39 AM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
If you are doing like JimmyHAD that should give...
If you are doing like JimmyHAD that should give you a blade edge running parallel to the top cap with equal blade exposure on both sides.
Just can't recall having the blade shift while tightening... -
11-03-2015, 10:49 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Yea, everyone is different. I like the short...
Yea, everyone is different. I like the short handle. How have you been aligning the blade?
Bob -
11-03-2015, 08:02 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Happy ending after all. Once you adjust to it you...
Happy ending after all. Once you adjust to it you may like it better. The blade aligns parallel to the top cap not the teeth on Merkur Slants. Simply put the top cap inverted on the counter, drop the...
-
11-02-2015, 03:31 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Sad man. I realize your beef was with the spot...
Sad man. I realize your beef was with the spot but you have to wonder why the treading is interrupted too. Checked my Merkur 37c again and the threads are not interrupted either.
Yea, so much for... -
10-29-2015, 06:48 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Yea, can't hurt any at this point. Bob
Yea, can't hurt any at this point.
Bob -
10-29-2015, 05:59 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
It also might be a courtesy to Merkur to inform...
It also might be a courtesy to Merkur to inform them that at least one flawed razor did get out to a consumer. The wet shaving community is really small and any word of a flaw spreads quickly so it...
-
10-29-2015, 03:52 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Was just a suggestion as an alternative to the...
Was just a suggestion as an alternative to the route you are going.
Hope you do get a full refund.
If you plan to post a review of the seller on here it might be a good idea to contact the mod... -
10-29-2015, 03:22 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
As annoying as the procedure is getting keep...
As annoying as the procedure is getting keep going and don't loose patience. It sometimes takes great persistence to get a good end result.
Have you tried contacting Merkur and explaining the... -
10-25-2015, 02:15 AM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Yes, I think you were just unlucky. Even German...
Yes, I think you were just unlucky. Even German made products suffer a quality control issue from time to time. Good luck with the outcome.
Bob -
10-24-2015, 10:19 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Be sure and let us know how it all shakes out in...
Be sure and let us know how it all shakes out in the end. To bad really, the 37C is one heck of a good shaver for me. Only a few others can shave marginally closer for me.
Bob -
10-24-2015, 09:42 PM
Thread: Merkur 37C Quality Control
by BobH- Replies
- 33
- Views
- 4,007
Yes, there are quite a few comments on the net...
Yes, there are quite a few comments on the net about the finish of Merkur DEs not being as good as the finish on EJ DEs. Personally I do not think the finish is terrible on my 37C and it may not be...
Results 1 to 11 of 11