Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Mocha Man mischievous's Avatar
    Join Date
    Sep 2007
    Posts
    203
    Thanked: 9

    Default Can anyone help explain this?

    I'm needing to take yet another break from shaving due to irritation in two areas.

    The base of my neck and my cheeks.

    I do 2 WTG everywhere then an XTG on my cheeks and a ATG pass on my neck.

    My beard is a mix of hair colors, black, brown, blonde, and gray. When doing the XTG on my cheeks I noticed small red bumps and small blonde hairs about .5mm in height sticking up, whereas all the black hairs are cut short. The blade makes a pronounced sound when I pass over this area.

    My neck is just a pain in the A*#! I have to do an ATG pass on my neck to be passable.

    I had trouble with the Alum bar and I had to give it a rest last week from that experience. I was getting small red bumps on my cheeks.

    Could this be a soap allergy? I do have irritation issues with my GFT cream and sometimes my TOBS sandalwood cream.

    Hasn't been to dry here so I don't think that's an issue.

    So, I think I can deal with the neck, but I'm at a loss about my cheeks.

    Any ideas?

  2. #2
    Senior Member blabbermouth Kees's Avatar
    Join Date
    Jun 2006
    Location
    The Netherlands
    Posts
    5,474
    Thanked: 656

    Default

    Is your blade sharp enough? Or overhoned? In both cases you might be muscling your way through the shave causing irritation. If you have a very tough beard a stiffer razor might be a solution as well.
    Plus ça change, plus c'est la même chose. Jean-Baptiste Alphonse Karr.

  3. #3
    Mocha Man mischievous's Avatar
    Join Date
    Sep 2007
    Posts
    203
    Thanked: 9

    Default

    If either, wouldn't I have these problems in other areas as well?

  4. #4
    Member AFDavis11's Avatar
    Join Date
    May 2005
    Location
    Virginia
    Posts
    5,726
    Thanked: 1486

    Default

    I would vote for underhoned. White and gray hairs are chemically different. Stronger and harder than "typical" beard hair. Thats for the cheeks. The neck is probably getting irritated because of the same condition, but not for the same reason. The neck skin has a lot of microfolds that the blade is probably abrading against. I would pull the neck super taut and go lightly. The microfolds are probably getting shaved at too great an angle.

    So, hone the razor a little more, and on your neck stretch it out much more and use a very low angle.

    Try that.

  5. #5
    Senior Member
    Join Date
    Jan 2008
    Location
    Northern California
    Posts
    1,301
    Thanked: 267

    Default

    Will your razor pass the HHT along the entire blade? If you leave hair behind, I don't care what color, your razor is dull. When you shave WTG and after the shave you still feel hair WTG your razor is dull. The only direction you should feel hair on your face when you are done with a pass is in the direction you have not done a pass yet. Stretching skin is another thing that, even with the grain, one should do. I have discovered that ATG is not something I can do on my neck unless almost all the hair is gone and I use a very light touch, I mean very light, and that can only be done with a really sharp razor.

    Take Care,
    Richard Adams

  6. #6
    Cheapskate Honer Wildtim's Avatar
    Join Date
    Nov 2006
    Location
    A2 Michigan
    Posts
    2,371
    Thanked: 241

    Default

    Definitely pay real close attention to polishing up your technique. For me it seems like every six months or so I end up with about a week of bad shaves that has me going back to the basics. I find that I tend to get sloppy after a while but I just don't really notice until I get so sloppy that I have some pretty irritating shaves. For me it starts on teh neck too thats where my blade angle is the most important and when I stop paying attention this angle is the first to vary.

  7. #7
    Mocha Man mischievous's Avatar
    Join Date
    Sep 2007
    Posts
    203
    Thanked: 9

    Default

    Well I am using two freshly honed and finished on CrO2 pasted strop razors. They have no problem passing every test we do so I'm at a loss about sharpness.

    I realize it's difficult to do an analysis over a few lines in a post but I really don't think its about sharpness in this case.

    I stretch my neck pretty taut but I'll concentrate on doing more.

    I think maybe I had a strong reaction to the alum bar and I am still feeling the effects.

    We'll see.

  8. #8
    Senior Member blabbermouth
    Join Date
    May 2006
    Posts
    2,516
    Thanked: 369

    Default

    Have you tried applying some hair conditioner, or other skin moisturizer, to your beard before applying your lather? If not you might give that a try.


    Scott

  9. #9
    Senior Member Sharp&Shiny's Avatar
    Join Date
    Mar 2007
    Location
    Basingstoke England
    Posts
    1,027
    Thanked: 112

    Default

    I used to have a similar problem.Try using a very light touch & a shollow angle going with the grain & very flat angle when going ATG this has helped me.
    I also use proraso pre shave cream before every shave & lots of moisturiser afterwards. I stopped using the alum block as it was drying my skin out too much.
    I've tried lots of different pre shave products & post shave ones but proraso preshave ceam & post shave milk has been the best I've used so they have now becme my standard products.Paul

  10. #10
    Ooo Shiny cannonfodder's Avatar
    Join Date
    Jan 2008
    Location
    Downingtown, Pa
    Posts
    1,658
    Thanked: 390
    Blog Entries
    1

    Default

    Your could try contacting The Gentlemens Quarter or Mama Bear and see if they can make you a non scented shaving soap. That would eliminate most of the allergens.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •