Results 1 to 10 of 22
36LikesThread: Breaks my heart...
LinkBack URL
About LinkBacksHybrid View
-
09-12-2018, 04:58 PM #1Senior Member
- Join Date
- Jun 2017
- Location
- Brugge , Belgium
- Posts
- 265
Thanked: 38
Breaks my heart...
will try to make the best of it though...:cry
RezDog likes this.I was tryin' to figure out which is worse,ignorance or apathy...Then I realized I don't know and I don't care...
-
09-12-2018, 05:03 PM #2Senior Member
- Join Date
- May 2014
- Location
- Easley, SC, USA
- Posts
- 1,861
Thanked: 480
We all share your pain...
bartds likes this.Some people never go crazy. What truly horrible lives they must lead - Charles Bukowski
-
The Following User Says Thank You to criswilson10 For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 05:43 PM #3Senior Member
- Join Date
- Feb 2018
- Location
- Manotick, Ontario, Canada
- Posts
- 2,814
Thanked: 563
Sad, but there is still a lot of blade there on which to set a new bevel after getting rid of the scars.
bartds likes this.David
“Shared sorrow is lessened, shared joy is increased”
― Spider Robinson, Callahan's Crosstime Saloon
-
The Following User Says Thank You to DZEC For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 06:00 PM #4Senior Member
- Join Date
- Feb 2016
- Location
- San Antonio, TX
- Posts
- 1,862
Thanked: 435
The blade is totally salvagable. With some 220 wet/dry sandpaper to clean the damage (rough stuff) then a progression up to 1200 grit (finish) you will be amazed at what you can do and save this fine blade. Set the bevel and hone and strop. It will be just like new. Good luck to you!
bartds likes this.Semper Fi !
John
-
The Following User Says Thank You to Johntoad57 For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 06:37 PM #5Senior Member
- Join Date
- Jun 2017
- Location
- Brugge , Belgium
- Posts
- 265
Thanked: 38
Thank you very much gentlemen
The width is a tad over 7/8"
Damage goes up to 7/8"
Wld you advise to bread knifing the blade (watched the Youtube vids by Gssixgun ) ?
Cheers
BartI was tryin' to figure out which is worse,ignorance or apathy...Then I realized I don't know and I don't care...
-
09-12-2018, 06:52 PM #6Senior Member
- Join Date
- Feb 2018
- Location
- Manotick, Ontario, Canada
- Posts
- 2,814
Thanked: 563
That is exactly what I had to do with a Puma with a chip in the blade.
That gssixgun video was excellent guidance for me.
BEFORE
AFTER
David
“Shared sorrow is lessened, shared joy is increased”
― Spider Robinson, Callahan's Crosstime Saloon
-
The Following User Says Thank You to DZEC For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 06:57 PM #7Skeptical Member
- Join Date
- Nov 2016
- Location
- Colorado Springs
- Posts
- 10,559
Thanked: 2197
I'd say go by Glem vid on repairing. It's good info. Then after you got that corrected, Fix the stabilizer as it will be too long and in the way of the blade. After all that, you should be good for cleaning and honing.
bartds likes this.It's just Sharpening, right?
Jerry...
-
The Following User Says Thank You to Gasman For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 07:01 PM #8barba crescit caput nescit
- Join Date
- Jul 2013
- Location
- Toronto, Canada
- Posts
- 9,680
Thanked: 2700
Agreed - always a shame to see these beauties injured.
But "breadknife" that razor, and it can be saved, and you will resurrect it to new life.....:-)bartds likes this.
-
The Following User Says Thank You to Phrank For This Useful Post:
bartds (09-12-2018)
-
09-12-2018, 10:32 PM #9Senior Member
- Join Date
- Jun 2013
- Location
- Pompano Beach, FL
- Posts
- 4,048
Thanked: 636
No problem. Breadknife the edge til chips are gone. Set bevel a d hone.
bartds likes this.
-
The Following User Says Thank You to bouschie For This Useful Post:
bartds (09-13-2018)
-
09-12-2018, 11:26 PM #10The Great & Powerful Oz
- Join Date
- May 2008
- Location
- Bodalla, NSW
- Posts
- 15,638
Thanked: 3751
You'll also need to address that stabiliser once the chips are gone.
The white gleam of swords, not the black ink of books, clears doubts and uncertainties and bleak outlooks.
-
The Following User Says Thank You to onimaru55 For This Useful Post:
bartds (09-13-2018)
Reply With Quote