Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23
Like Tree8Likes

Thread: Another Paste Question

  1. #11
    Know thyself holli4pirating's Avatar
    Join Date
    Feb 2008
    Location
    New York
    Posts
    11,930
    Thanked: 2559

    Default

    Quote Originally Posted by pixelfixed View Post
    Is interesting to note,most of the true honemeisters on this site have done a huge amt.of testing on pastes and sprays.
    But do they use them on a regular basis?
    I would bet not,can pastes and sprays re-fresh an edge? to a point perhaps.Are pastes and sprays a panacea to a true finishing Hone?
    do they work long term? what is the allure newbs have for pastes and sprays? and why? Cost? assumed ease of use?
    I have tried all the pastes and sprays.
    I don't know about now, but for some time, Lynn was going to a diamond spray on hard wool felt to finish all of his razors. Perhaps he will comment on his findings and whether or not he's still doing so.

    I sometimes finish with chrome ox on the SRD webbing. I like it a lot, and have received positive feedback on it from others. I really don't think it matters how a razor is finished, paste vs hone, but maybe I simply have not experimented enough.

    Paste can definitely refresh an edge, if its not too far gone, though maybe not indefinitely. I would say a pasted strop is definitely easier to use and definitely less expensive than the average finishing hone.

    To respond to the OP, there is more to the equation, be it with pastes or hones, than just the grit rating. How the grit wears, how much the grit is exposed above the binder/material, the shape of the grit, how fast the binder breaks down to expose more/fresh grit, how flexible the surface is (more for strops), etc etc all matter. In order to figure out what works where for you, you'll need to experiment. You can definitely draw off of the experience of others, and you can use grit ratings as a guide, but grit ratings are not the end all and be all of it.

  2. #12
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    Quote Originally Posted by holli4pirating View Post
    I don't know about now, but for some time, Lynn was going to a diamond spray on hard wool felt to finish all of his razors. Perhaps he will comment on his findings and whether or not he's still doing so.

    I sometimes finish with chrome ox on the SRD webbing. I like it a lot, and have received positive feedback on it from others. I really don't think it matters how a razor is finished, paste vs hone, but maybe I simply have not experimented enough.

    Paste can definitely refresh an edge, if its not too far gone, though maybe not indefinitely. I would say a pasted strop is definitely easier to use and definitely less expensive than the average finishing hone.

    To respond to the OP, there is more to the equation, be it with pastes or hones, than just the grit rating. How the grit wears, how much the grit is exposed above the binder/material, the shape of the grit, how fast the binder breaks down to expose more/fresh grit, how flexible the surface is (more for strops), etc etc all matter. In order to figure out what works where for you, you'll need to experiment. You can definitely draw off of the experience of others, and you can use grit ratings as a guide, but grit ratings are not the end all and be all of it.
    I can't figure out what that other guy is even talking about Dylan and his bet is not out of any kind of familiar knowledge in my opinion. I think the guy is just contrary sometimes because this is the internet. Us old guys can just be contrary sometimes don't cha know..... I think the biggest problem with pastes and sprays, especially for new guys is that they use either too much media, too many strokes or too much pressure.

    In any case, I still use both .5 micron diamond spray and chromium oxide spray and paste all on felt for the most part these days. Occasionally, I will use the chromium oxide crayon on the poly webbing or cotton canvas too. I still find that 4-5 strokes at the end of a honing regiment unless I am using a 20K or 30K stone adds that little extra smooth and sharp to an edge. I still also find that 4-7 strokes is a sweet spot for refreshing when a razor starts to pull and can be done about once a month for a long time before needing to go back to the finishing hone, YMMV. I still hone razors 4-6 hours a day almost 7 days a week, so I can only give you my opinion on what works for me, but I can tell you that if something does not provide results consistently, it does not last long over here unless I am just experimenting.

    You can shave off an 8K comfortably. You can shave off a 12K or finishing stone more comfortably. On the finishing stones and even higher grit finishing stones, YMMV depending on your ability, the razor and your agenda.

    Have fun.
    Last edited by Lynn; 04-03-2013 at 01:19 AM.
    Johnus likes this.

  3. The Following User Says Thank You to Lynn For This Useful Post:

    jc50 (04-03-2013)

  4. #13
    Senior Member blabbermouth
    Join Date
    Jan 2011
    Location
    Roseville,Kali
    Posts
    10,432
    Thanked: 2027

    Default

    Lynn,do you use pastes and sprays on all the blades you hone??

  5. #14
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    Quote Originally Posted by pixelfixed View Post
    Lynn,do you use pastes and sprays on all the blades you hone??
    I don't as on most of them I finish with a 20K or 30K stone these days. Sometimes if one is just not how I like it, I might do one or two strokes on a sprayed chromium oxide felt strop I have hanging in the laboratory to get it there. If that doesn't work, back to the hones. I used to do 10 strokes religiously on either .5 micron diamond spray or chromium oxide after the finishing stone simply because I like the results and the consistency. It's not that you can't get a nice shave off just the stones, but this is just my preference for a better edge and shave based on my experience.

    The only other thing I can say here is that I have found that what is working today, may not work as well tomorrow or something may come along that works better for you. I think that's why I still keep experimenting even though the process I use today is working so well. Not 100% but close. There is always one where the bevel wasn't right or something just didn't work on that razor and another go around is needed, but it's not often. The other thing is that many razors shave differently based on size, width, balance, wear and even the way they are pinned. So many variables. I think that's why it can be so hard for new guys considering some of the razors I am seeing them try to hone and shave with.

    Have fun.
    pixelfixed and jc50 like this.

  6. The Following 2 Users Say Thank You to Lynn For This Useful Post:

    jc50 (04-03-2013), pixelfixed (04-03-2013)

  7. #15
    Senior Member mjsorkin's Avatar
    Join Date
    Nov 2006
    Location
    New Jersey
    Posts
    1,139
    Thanked: 173

    Default

    I've got a friend in south Jersey who has two grits of the Dovo paste and he really has had some great edges off of it. I have no experience with them but I'm hoping to try out one of his pasted strops the next time I see him.

    If I were buying Dovo paste, I'd try to get the finest one, or the two finest. Do a few strokes on it and see what happens.

    Michael
    “there is the danger that the ignorant man may easily underdose himself and by exposing his microbes to nonlethal quantities of the drug make them resistant.”---Fleming

  8. #16
    Member danxaz's Avatar
    Join Date
    Nov 2011
    Posts
    67
    Thanked: 2

    Default

    Now I am really confused. If you're finishing on a 20 or 30k stone, do I have to touch up my razor on that high grit to make any difference? So, in general, to touch-up a razor one needs to go back to the highest grit stone it was finished on?

    Let me be clear what I'm trying for here. I have little to no interest in honing from start to finish. Not yet anyway. I have one razor, A Boker King Cutter. My mane interest is in using this razor daily, which I do, and aintaining the edge as long as possible before having to send it to get honed agian. When I do send it out, do I need to know the Honmeister's finishing set-up so that I can duplicate it on touch-ups? Or is my little barber hone good enough? Or do I need to get a higher grit hone to touch-up?

  9. #17
    Senior Member Mephisto's Avatar
    Join Date
    Feb 2012
    Location
    NC
    Posts
    1,408
    Thanked: 126

    Default

    If you want the same type of edge you would have to duplicate. However, if you drop down to a lower grit you can still get a fine edge.

    So, for example, if I had a razor honed by Lynn, finished on a 20k stone and liked that edge I would have to get a 20k stone. Plus, you have to take other things into account like skill level. I am sure Lynn's edge of a 20k would be better than my edge of a 20k.

    Not trying to brown nose, he just has more experience than me. Luckily, one day he will die and I can catch up.

    For maintenance you could just use some Crox. Will it be as good as 20k? Don't know. That will be for you, the end user, to decide. Honestly, I think you want a concrete answer and there are some many things to consider.

    Having said that, my set up, that works at the moment is a diamond spray regimen and crox. It works to keep the edge maintained. I use 1 micron, .5 micron and finish with Crox.

    Someone could say that this is terrible because they only use the finest Japanese water stone or some other expensive stone. I say pooey and when you feel like buying me a 500 dollar plus stone I will gladly use it.

    Overall, do not try to get to tweaked over this stuff. It will in time and you will get little lightning bolt moments of understanding.

    Quote Originally Posted by danxaz View Post
    Now I am really confused. If you're finishing on a 20 or 30k stone, do I have to touch up my razor on that high grit to make any difference? So, in general, to touch-up a razor one needs to go back to the highest grit stone it was finished on?

    Let me be clear what I'm trying for here. I have little to no interest in honing from start to finish. Not yet anyway. I have one razor, A Boker King Cutter. My mane interest is in using this razor daily, which I do, and aintaining the edge as long as possible before having to send it to get honed agian. When I do send it out, do I need to know the Honmeister's finishing set-up so that I can duplicate it on touch-ups? Or is my little barber hone good enough? Or do I need to get a higher grit hone to touch-up?
    Last edited by Mephisto; 04-03-2013 at 07:29 PM. Reason: added more info
    From their stillness came their non-action...Doing-nothing was accompanied by the feeling of satisfaction, anxieties and troubles find no place

  10. #18
    Pasted Man Castel33's Avatar
    Join Date
    Jul 2010
    Posts
    1,283
    Thanked: 269

    Default

    Mephisto has lead you in the right direction.

    Just to give you an idea of what you can achieve with paste here is my typical honing method of late.

    I use a king 1k hone to set my bevel. I then go to a four sided leather paddle strop that has a stropping surface of 12in long and 1.25in wide pasted with 9 micron diamond, dovo green, dovo red and dovo black.

    I do 200 laps on the 9 micron, then 500 laps a piece on all the dovo paste.

    I then use that razor till it starts to pull. Once that happens the razor needs a touch up.

    Typically about 100 laps on black would bring my edge back good. If not I will then do 100 more laps. If nether of those work I drop down to the 9 micron and start over.

    In your case you only have dovo red. So when you start to notice your razor is not performing the way you like you would go to you pasted strop that has the dovo red. The number of laps you would have to do to bring the razor to shave ready will be different cause your paddle will be different but that is something you will have to learn as you go.
    Mephisto likes this.

  11. #19
    Senior Member Mephisto's Avatar
    Join Date
    Feb 2012
    Location
    NC
    Posts
    1,408
    Thanked: 126

    Default

    I am sort of doing the same thing as Castel. I set the bevel on a Norton 1k. However, you do not have to worry about bevel setting yet.

    I use a four sided paddle strop next with 9 micron, 3 micron and 1 micron diamond paste or spray. I sometimes will go to a Norton 4/8 though just to see the difference.

    I am thinking of going 9-6-3 for my next set up though. I finish with .5 diamond spray and crox. To maintain my razor I just go back to the crox and .5 spray.
    From their stillness came their non-action...Doing-nothing was accompanied by the feeling of satisfaction, anxieties and troubles find no place

  12. #20
    Member danxaz's Avatar
    Join Date
    Nov 2011
    Posts
    67
    Thanked: 2

    Red face

    Quote Originally Posted by Mephisto View Post
    If you want the same type of edge you would have to duplicate. However, if you drop down to a lower grit you can still get a fine edge.

    So, for example, if I had a razor honed by Lynn, finished on a 20k stone and liked that edge I would have to get a 20k stone. Plus, you have to take other things into account like skill level. I am sure Lynn's edge of a 20k would be better than my edge of a 20k.

    Not trying to brown nose, he just has more experience than me. Luckily, one day he will die and I can catch up.

    For maintenance you could just use some Crox. Will it be as good as 20k? Don't know. That will be for you, the end user, to decide. Honestly, I think you want a concrete answer and there are some many things to consider.

    Having said that, my set up, that works at the moment is a diamond spray regimen and crox. It works to keep the edge maintained. I use 1 micron, .5 micron and finish with Crox.

    Someone could say that this is terrible because they only use the finest Japanese water stone or some other expensive stone. I say pooey and when you feel like buying me a 500 dollar plus stone I will gladly use it.

    Overall, do not try to get to tweaked over this stuff. It will in time and you will get little lightning bolt moments of understanding.
    Well I'll be damned if I don't feel better. Especially after learning that some stop with stones after the 1K mark. Thanks all for the help. I think I will be fine
    Mephisto likes this.

Page 2 of 3 FirstFirst 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •