Results 1 to 10 of 13
Like Tree1Likes

Thread: Factory locking washer look

Hybrid View

  1. #1
    Junior Member
    Join Date
    Jun 2013
    Posts
    10
    Thanked: 1

    Default Factory locking washer look

    Trying to replicate the look of factory locking washers used on vintage razors. (and modern razors for that matter). Current I simply just dome the washer and peen away. They look fine, but the factory washers definitely look different on most vintage razors. The factory washers have more of a pronounced shoulder instead of a half sphere look and the finish pinning looks like it's almost counter sunk into the washer. Anyone know of a technique or trick to get that look?

  2. #2
    Senior Member blabbermouth Substance's Avatar
    Join Date
    Jun 2013
    Location
    Gladstone QLD AUSTRALIA
    Posts
    3,245
    Thanked: 804

    Default

    Some of the ones I have removed have the same finish like a countersunk dome with a smaller washer inside the dome usually nickel,
    I have tried to make them by doming and then centre popping the dome back down. But I need to rethink my tool shapes to get it to look right and I don't have any nickel washers small enough for inside the domes yet
    Saved,
    to shave another day.

  3. #3
    Senior Member AirColorado's Avatar
    Join Date
    Apr 2009
    Location
    Boulder County CO
    Posts
    1,004
    Thanked: 127

    Default

    I was just thinking about this a few days ago! Pulled a pair of collars off of a scale and noticed that they were more of a half doughnut rather than a simple dome. Was thinking maybe dome the washer and then flip it over and dome again using a much smaller doming "bit" and larger hole. That's just in my mind's eye - haven't tried it yet.

  4. #4
    Senior Member ScienceGuy's Avatar
    Join Date
    Sep 2011
    Posts
    1,650
    Thanked: 1342

    Default

    The old collars were made by punching a relatively thin sheet of metal with a die. There were usually two sets - the outer display collar and an inner one for reinforcement. To replicate the effect exactly, one way is to experiment with punching thin sheets of metal. For an idea of the process see here: http://straightrazorpalace.com/works...ld-school.html

    Another that might work would be to use thicker washers, and bevel the outside edge and countersink the inside.

  5. #5
    Senior Member miha's Avatar
    Join Date
    Apr 2013
    Location
    Slovenia
    Posts
    489
    Thanked: 83

    Default

    hi,.. just as an idea,.. I accidentally found flower like washers in a hobby/jewelery store.. see pic below, I just tried them on one razor 2 days ago,.. was a bit afraid that I might ruin them if peening so I went for the screws (which I like more anyways), although I think yellow brass center dome would look nice on flowers washers .. 1 thing though, if you use these pounched brass "stacked" washers, aren't they too fragile, meaning they might get flattened while peening, or at least damaged, someone mentioned you can use support inside, so is this the solution, eg 3 stacked washers under the "stacked" punchout?.. I have an old ca johnson with flower washers that where I will have to use the originals and peening..


  6. #6
    Junior Member
    Join Date
    Jun 2013
    Posts
    10
    Thanked: 1

    Default

    Quote Originally Posted by AirColorado View Post
    I was just thinking about this a few days ago! Pulled a pair of collars off of a scale and noticed that they were more of a half doughnut rather than a simple dome. Was thinking maybe dome the washer and then flip it over and dome again using a much smaller doming "bit" and larger hole. That's just in my mind's eye - haven't tried it yet.
    Half doughnut is a perfect analogy. Almost feels like you would need some kind of punch and die set. Anyone know of a really really small doughnut punch and die set. ha... ha..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •