Printable View
I have just bought a boker no 386.
its not in too bad a condition, no rust, scales clean and whole and the markings sharp and deep.
My problem is it looks like it has been previously 'restored' just very badly. I think it has dremel marks or some other power tool does anyone have any ideas on how to get rid of them? currently i am just working at it with 280grit sandpaper.
sorry the picture isn't great but you get the idea of what i mean
cheers
Attachment 167445
Some/many blades display "grind" marks. Given that the "markings are sharp and deep", I'd consider that, before going any further.
I wrap strips of wet dry sand paper around old wine corks and wet sand with WD-40. After I have gotten to 2kgrit I use steel wool and mothers, and then just mothers. Start with a higher grit 1k or 1.5k and drop down or climb up as need be.
Try sanding in the opposite direction as the marks. Horizontal verves vertical. About 50 strokes, then check for progress, It should lessen the appearence. Then switch to circular sanding motion 50 circles. Alternate as needed. You see I did the same thing, thats how I fixed my Opps . Ok truth is after I did it a second time, I took a dremmel with the steel wool attachment to it on low speed and that fixed it in about 30 seconds.Your choice keep us posted on how things go.
I've come to the realization on a couple of occasions that I don't have to be a slave to one method or the other while going through a repetative up and down cycle of hand sanding or a back and forth with the buffer grits to remove scratches missed on previous passes. Sometimes an intervention with the other method with the appropriate grit seems to get things back on track. (just what the comparative grit between the two is still not clear to me but I err on the side of caution) I still think there are places that buffing just won't work well.Quote:
Originally Posted by ultrasoundguy2003
pic is not good enough to see, but all razors have grind marks.
If you can take a pic that shows the blade better I will be able to tell you if the grind marks are Dremel or belt.
ok i think i have done an alright job on at least minimising it. just used wd40 and sandpaper from 280-2000. it can only be seen on the right angle and right light. its a pretty schmick razor, its a shame i am giving it to a buddy for his 21st.
cheers for all the help
and thanks rezdog for the wine corks tip! it makes it a lot easier!
#0000 steel wool?Quote:
Originally Posted by RezDog
Joe
Quote:
Originally Posted by dooey
+1. After hearing this tip on another thread, I ordered 100 wine used wine corks, figured I'd get a variety and see what works best. I'm already using them. I'm alternating between them and two other backing pieces, to see what works best. One backing piece is an ordinary eraser. That's good especially for flat surfaces. The wine cork is especially good for getting into hollows. That's true also of the third backing piece, a hunk of 5/8 thick rubber tubing:
Attachment 168307
I got the tubing idea from another SRP contributor. I'm still waiting for the 7/8 tubing to come in, but I imagine it will be similar to the wine corks. My larger corks are 13/16, except the ones that are mushroomed shaped. They're wider, but the mushroom bulb gets in the way.
I started with the picture of the eraser alone, and deleted it to replace it with a picture of all three backings. I find that if I try deleting an image, it shows up anyway as an attachment. Anybody know how to get rid of one of those?
Joe
Yes. The synthetics works as well. I seem to recall having used 000 with mothers once then the 0000 but it was because my blade was still really scratchy looking. It is not very aggressive so you can play around with then a little bit and if it isn't where you need to be it doesn't take long to remove it. Compared to many here I'm still fairly novice and still messing about trying to get my methods perfected.Quote:
Originally Posted by carrolljc
When I need another wine cork I just open another bottle ;)Quote:
Originally Posted by carrolljc
I made a little promise to myself at one point: no sanding razors while imbibing. Maybe taking razors out and admiring them, but even that might not be altogether safe.Quote:
Originally Posted by gugi
I got home from a trans-Atlantic flight a few months ago, totally exhausted, jet-lagged. Got up in the morning and started to shave, and gouged a deep cut in my jaw. Worst cut ever. When driving, I figure exhaustion is equivalent to having had two stiff drinks, and try to compensate accordingly (slow, careful, attentive). Same rule of thumb seems to apply for handling sharp objects.
But then, that way of acquiring corks sounds like a lot more fun than just buying a bag full.
Joe
