Thread: Gold washed blade

This may seem like a stupid question to you guys who have a lot more experience than I do...but I have been watching Lynn's DVD and have an inquiry. I recently purchased a rather nice razor from ebay, but there is a bit of tarnish (not rust, as far as I can tell) on the blade and I would like to clean it up a bit. Lynn recommends MAAS polish, but this blade has a "gold wash" logo, and I don't know what the polish might do to it. Do I leave it "as is" or can I safely use a polish on it? The razor is not a prized collectors' item, but I don't want to damage it either. Thanks for your help.

Try going around the logo. If not possible, it all depends on how much you like the gold wash.

I had the same problem and it seemed all comercial tarnish removers and polishes with remove the gold along with the tarnish. All depends how heavy the tarnish is but I used this and it worked pretty well..

1 part liquid soap
1 part salt
1 part baking soda

Line a pot with aluminum foil bring to a simmer stirring with a wood spoon gently.

Let stand for 15 to 20 min.

Rub gently with toothbrush and let it sit on blade for 15 minitues.


Got this from my daughter who is a doc but majored in Chemistry.

I used some Maas on my C-Mon Filly, and it took the gold wash off as quickly as it did the tarnish...oh well, live and learn.

-Pary

Any other suggestions or experience with vincebell's method, gents? I'm about to try to remove some tarnish and keep some gold wash this weekend . . .

depending on the shape, size, ect of the logo you could always cover it with clear tape and then cut the outline with an exacto knife.

I might 1) cut it a little big to stay away from the gold, besides, light tarnish will come off with use, soap, stropping, wiping on towel, ect
2) I would anneal the blade of the exacto knife before I did it to keep from scratching the razor blade where you cut the tape.

Simply heating it orange hot by laying it on an electic stove burner and turning the stove on high and leaving it on the burner when you shut it off so it will cool slowly due to residual heat in the burner element should do it.

I would still test it on the shank, inside the jimping, somewhere to see if it will scratch the razor blade before I used it.

And for gods sake, don't cut over the gold, it will come off for sure if you scrape it with a knife blade !!

Good luck

Originally Posted by vincebell

I had the same problem and it seemed all comercial tarnish removers and polishes with remove the gold along with the tarnish. All depends how heavy the tarnish is but I used this and it worked pretty well..

1 part liquid soap
1 part salt
1 part baking soda

Line a pot with aluminum foil bring to a simmer stirring with a wood spoon gently.

Let stand for 15 to 20 min.

Rub gently with toothbrush and let it sit on blade for 15 minitues.


Got this from my daughter who is a doc but majored in Chemistry.

Should this result in a liquid or a thick, gritty paste? I tried it and found that the paste tended to burn, rather than simmer in the lined pot. It seems like the mixture needs more liquid?

The resulting paste was too dry to even stick to the blade, so I added water and applied it to the blade. It removed some tarnish (and left the gold wash!), but left some spots. I'm inclined to try adding water to the paste and letting the blade soak for several hours or starting fresh, with a mixture that includes more liquid, so I can actually get the mixture to simmer. Thoughts?

I believe the aluminum is suppose to 'attract' the 'tarnish' from the blade using the heat and electrolites (salts)....

I do not think you are suppose to coat the blade....

BUT, it's not my experiment so I might be wrong

C utz

Bringing this up again, as I'm suddenly interested. Has anyone tried THIS

Same maker as Renaissance Wax.