15 Attachment(s)
How to make a traditional set of horn scales ... the way I do it.
My last tutorial seemed well received so I thought I'd try another.
I selected a piece of black horn I received from Masecraft Supply which was nice and flat. It doesn’t always work out that way. If they are not flat on the inside surfaces they need to be. There are a number of ways you can approach this but I recommend you wait until you have band sawed the scales to their basic shape as sometimes they warp after they are cut. I think because some of the natural stress is relieved when it is cut. It’s also easier to flatten 2 small scale halves than a large blank. If I have to flatten the scales then I polish them inside when they are done. It not only gives them a finished look and improves the transparency but I think it helps any water runoff and helps prevent the accumulation of gunk.
Since this tutorial is geared toward the beginner I’m not going to draw my scales by hand. I have a box full of old scales. I throw just about nothing out. I’ve picked a scale that is pleasing to the eye and not too big or too small for the 13/16 near wedge Wosti.
Attachment 222539
Attachment 222540
Lay the scale on a piece of paper and trace around. This will have a wedge that is 9/16” long. A very common size based on a large number of wedges I’ve measured. It also looks aesthetically correct. Draw a line on the scales were the wedge will end.
Attachment 222541
Lay your blade on the drawing. Most folks like the blade tucked up close to the wedge. I like mine 1/16” to 1/8” from the wedge. If you get it closer than that you run the chance the blade will hit the wedge. Some pivot pin holes are large and the blade is going to move around some during the life of the razor. A lot of the older razors had the blade further from the wedge. I recommend you go no more than 1/4".
Attachment 222542
Now that we have located the pivot pin hole on the drawing you can see the scales are too long. A good rule of thumb is the distance ofthe tang hole to the end of the scales is 1/2 the length of the tang. Some tangs are very long so that would be out of place. 1/2” from tang hole to the end of the scales is another good rule of thumb. So slide the pattern scale back until the pivot hole lines up with where you want the pivot pin and redraw the end of the scale.
Attachment 222543
You need 2 scale patterns so fold the paper in half and cut the pattern out. Take your time, be precise and stay to the inside of the line or the scales will be too fat.
Attachment 222544
I use an Elmer’s stick glue to glue the patterns to the scale material.
Attachment 222545
Now over to the bandsaw. Leave about a kerfs’ width as the horn will break out some on the bottom. If you cut right up to the line your finished scales will have broken edges. The 1” x 42” belt sander with 80 grit will make short work of the excess material.
Attachment 222546
Once the scales are cut out use double sided scotch tape to put them together. Some folks use carpet tape. This is thinner so I like it better. The scales will stay together now until the final polish.
Attachment 222547
Next it’s over to the belt sander. Take the excess material off right down to the edge of the paper. You don’t want big scales so follow the pattern right to the edge of the paper.
Attachment 222548
If you are happy with the shape it’s time to drill the pinholes. Mark a point 1/8” behind the edge of where the wedge will be and draw a line. Measure it, divide by 2 to get your pin location. Mark it and use a punch for the drill bit to locate on. I use a scribe and push it into the material rather than a punch and hammer. With some material you might create a crack using a hammer. Use the same method for the pivot pin hole. Get it right. Nothing worse than off center pins.
At the drill press I use a .067 dia. bit. A 5/64 will be OK. I use a tapered reamer later to open the .067 hole more and give the hole some taper. You want the hole bigger than the 1/16” rod so you can close up the scales to the wedge and move things around some to help with centering the blade later.
Attachment 222549
Attachment 222550
Attachment 222551
With the holes drilled it's time to thin out the scales on the belt sander. Don’t forget your respirator and I have a dust collector hooked up to my machine. I hold the scales up to the belt and work it back and forth taking no more than 2 passes before I turn it over and make another pass. I take one side down to final thickness at a time. You want no more than .120 thickness. I’ve measured a ton of scales and they average .120 to .110. .120 on a large blade, say a 1” chopper, and down to say .095 on a smaller blade. For this I chose .110 and after finish polish it measured .105. You can thin these out on other types of sanders but I have the most control with this and it’s fast with an 80 grit belt.
Attachment 222552
Check the scales as you remove material. They will get hot and can warp. If they do, bend them back straight. If they are warped your blade will not center.
Attachment 222553
This part is sort of difficult to explain. It would be easier in a video. I hold the edge of the scales to the belt at a high angle and make 2 passes along each edge. Cutting to about half the thickness of the scales to the edge.
15 Attachment(s)
How to make a tradition set of horn scales ... the way I do it. PART 2
Attachment 222559
Attachment 222560
The next pass is one each at about 45 degrees which meets up with the line of the previous cut.
Attachment 222561
Attachment 222562
Now back to the edge again at a high angle as before going as close to the edge as you dare say within .010 but do not go over the edge. You will ruin the finished lines of the scales. It can be corrected but it takes more work. The last pass around the scales are almost flat against the belt.
Attachment 222563
Attachment 222564
Attachment 222565
Lastly dress the ends down tapering from just behind your pin holes just up to the edge. As before do not go over the edge or you will destroy the lines of the scales.
Attachment 222569
This next step is a real time saver and saves a ton of sanding. I use a scraper to shape the scales at this point. A quick touch on the belt sander creates a burr on the scraper’s edge that cuts smooth and efficiently.
Attachment 222570
Attachment 222571
Attachment 222572
Attachment 222573
Attachment 222574
Attachment 222575
Attachment 222584
Before there was sandpaper this is what the old timers used. As you can see in the photo, I do half a scale side at a time working from the edge toward the center. Don’t go over the edge. We are working the facets created by the sander into a gradual curve.
12 Attachment(s)
How to make a traditional set of horn scales ... the way I do it. PART 3
Attachment 222586
Attachment 222585
Attachment 222587
Attachment 222588
Attachment 222589
Attachment 222590
With the scales sort of smoothed up I use a single cut draw file (any single cut file will do) working along the length of the scales about half a side at a time like with the scraper. This draw filing will straighten out any high/low spots in the scales created by the belt sander. You can easily see these in the photos once you start filing because you scraped the scales smooth.
Attachment 222591
Attachment 222592
Once the draw filing is done use the file to shape the ends of the scales. Work from just behind the pin hole to the edge. Once again don’t go over the edge. You want a long gradual line here not just an abruptly rounded over end. Now scrap the scales a second time to remove all the file marks. When finished you should have nice smooth true surfaces. This is much faster than sanding and you do not have to contend with removing deep scratches.
Attachment 222593
The sanding is next. You only need 4 grits. Start with 320 wet/dry paper. No need for courser. The scraper cuts very smooth. I choose wet/dry because the glue holding the grit is better and it cuts faster. I use it dry. You might want to wear a dust mask during this. You can do it wet but I don’t like the mess. The paper is backed with a piece of hard felt. Don’t use your fingers. You can create waves in the surface because your fingers are too soft. Plus it’s hard on the fingers. Sand lengthwise on the scales. Now you can sand to the very edge of the scales to remove the last of the belt sanding marks. Don’t spend any more time on the very edges than what is necessary to remove the sanding marks. You do not want to change the lines of the scales you’ve worked so hard to keep. Like a pretty woman everything is curves. No straight lines.
Attachment 222594
Attachment 222595
Attachment 222596
400 grit followed by 600 grit and last 1200 grit. I do this sanding process wearing 3 power magnifiers. I also use a shop light to create shadows as I work so I can see any scratches or irregularities that need to be removed. I rarely have to come back and remove scratches after buffing.
8 Attachment(s)
w to make a traditional set of horn scales ... the way I do it. PART 4
Attachment 222597
Attachment 222598
Now the fun part is buffing to bring out the beauty of the horn. I use a stitched spiral sewn cotton 4” or 6” wheel with Jantz’ Black Magic. I like this because it’s not greasy and polishes quickly. I’ve tried a half dozen different greaseless compounds and I find this best for me. Last I buff with Jantz’ Pink Scratchless on the same type of wheel. The scales now shine like a piece of black glass.
This whole process takes me about 2 hours from paper pattern to final polish. But since you are just starting out time is of no consequence.
Attachment 222599
Attachment 222600
Attachment 222601
All that is left is to separate the scales, I use a small box cutter, and remove the tape and residual glue. I use automotive bug remover made by 3M for this. There is a product called Goo Gone that works but it leaves and oily film on the scales. The edges of the scales can be very fragile and I break them with a piece of 1200 grit paper along the inside edge of the scales. Stay away from the area where the wedge will go. You want that sharp crisp edge. Note the use of a tapered reamer to remove foreign matter from the pin holes.
Attachment 222602
Attachment 222603
Attachment 222604
You are done and so is this tutorial. Too long I fear. Nothing left but to fit your wedge and pin the razor.
There is more than one way to skin this critter but my hope is this saves some major pitfalls for those just starting out particularly with the poorly proportioned, thick and clumsy looking scales with off center pins placed too close to the ends of the scales. Unless you get crazy with the wedge the razor will balance nicely in the hand in the center of the tang.
For you folks with experience making scales, my hope is there is something in this tutorial for you too and you enjoy reading it as much as I did putting it together.
Regards,
Karl