Help getting that mirror finish

So I'm struggling a bit on getting my blades to a mirror finish.
It just seems like I can always see a scratch in the metal. I've done hand sanding through 600 (usually trying to start on the lowest grit possible) Then wet micro mesh and I've buffed on a Beal Buff system with Tripoli and white dimond compound. I've then hand polished with MAAS metal polish. These are 3 blades I've been working on (the wedge was in the worst shape) I just cant seem to get ALL the scratches from the hand sanding out. (Or am I just being too picky) I've been thinking about a cheap Harbor freight tumbler- Do you guys find that those make a significant difference? I have no idea why some of these are upside down and not sure how to fix.

Attachment 262870
Attachment 262871
Attachment 262872
Attachment 262874
Attachment 262873
Attachment 262875
Attachment 262876
Attachment 262877
Attachment 262878

A true mirror finish is nearly unattainable, but you can get very close I think. For a near mirror finish I usually hand sand to 3000 and then polish by hand as well after that. I don't have a buffer or tumbler so I can't give advise on those tools, though many people have good success with them. You are only sanding to 600? Next try 800, 1000, 1500, 2000, 3000, then use some method of polishing. Even if it ends up looking like a mirror, magnification will surely reveal more scratches. Sometimes you just have to know when enough is enough.

Keep going on hand sanding. Over 1000 should get you there

I don't think I have ever mastered the mirror finish. I hand sand with 400 and then buff with 600 and then wet hand sand to 2000 then emery, tripoli, white then red. There is often scratches left behind. It does not matter to me. I understand that to get them out, once they appear, you have to back up one step, maybe two and take another run at it. Part of why I don't care about getting a mirror finish is they are very time comsuming to do and they mark quite easily. I am happy with pretty shiny and clean. I am going to hone them and use them and they will be scratched.

Quote:

---

Originally Posted by xiaotuzi

A true mirror finish is nearly unattainable, but you can get very close I think. For a near mirror finish I usually hand sand to 3000 and then polish by hand as well after that. I don't have a buffer or tumbler so I can't give advise on those tools, though many people have good success with them. You are only sanding to 600? Next try 800, 1000, 1500, 2000, 3000, then use some method of polishing. Even if it ends up looking like a mirror, magnification will surely reveal more scratches. Sometimes you just have to know when enough is enough.

---

No sanding to 600 wet sand paper then using Micro Mesh 2x2 Pads through all the grits from 1500 to 12000

I think the advise of sometimes knowing when enough is enough is what I needed to hear. I'm a bit of an obsessive perfectionist when I do things and can be a bit over critical of my own work.

Quote:

---

Originally Posted by ssgmeader

No sanding to 600 wet sand paper then using Micro Mesh 2x2 Pads through all the grits from 1500 to 12000

---

The jump from 600 to the Micro Mesh pads is a big one.
3M has finer paper than 600...
I am not sure this link copied well but there are 3M wetordry polishing paper.
Walmart has wetordry Sandpaper - 1000, 1500, 2000, and 2500 and 3M has finer..

http://multimedia.3m.com/mws/media/2...20FINAL_R2.pdf

Each grit like honing needs to remove the scratches from the previous. Too big a jump
and you are never done.

So, how bad was the pitting, do you have photos?

What is the lowest grit you tried.

You must remove all the surrounding metal, to the depth of the lowest pit. Only go as low in grit as needed or you will, spend more time removing the deeper scratches.

Typically, I start at 600, then drop down in grit a little at a time until I am making progress, removing the damage. Sometimes it is easier to use a bit higher grit and spend more time removing the damage than using a lower grit and spend more time removing the scratches you made with lower grit.

The mistake most folks make is not spending enough time on the lowest grit and removing all the pitting.

I see original pitting in your finish. Sand from heel to toe, then from edge to spine, removing each scratch pattern. It will leave a more uniform pattern and remove metal faster, also use a cork backer, wrapped in 6mm craft foam.

Once all the pitting is removed and you have a uniform finish, then move up, if you have a uniform base, the finer grits go quickly.

I go to 2k W&D then buff, you can hand polish after 2k or use micro mesh. Buy good paper, cut into 3 inch squares and change it, when it stops cutting.

Almost always, a defective finish is from not spending enough time at the lowest grit.

Dull your edge, with a diamond file, plate or sand paper, it will make it much safer to sand, you will have to re-hone when done anyway.

I do not like the finish of tumblers, they remove all the sharp lines and detail. Have one never use it for razors.

Quote:

---

Originally Posted by ssgmeader

No sanding to 600 wet sand paper then using Micro Mesh 2x2 Pads through all the grits from 1500 to 12000

---

Oh, ok. I haven't used Micro Mesh before so I might not be of much help. Sounds like it should be plenty high enough grit. Are they the cushioned square pads? Maybe they're too squishy for what you are trying to do. What are you using as a "backer"? A cork is pretty common as a backer with sandpaper, I use a piece of dowel for a harder backer. Probably just need more time at each level before moving on. Good luck with it, I hope you have a good outcome.

You might try buffing with Chromium oxide after 2000 grt. W/D paper, followed by Maas or flitz or even 3M metal restorer/ polish.

Quote:

---

Originally Posted by outback

...or even 3M metal restorer/ polish.

---

Ahh, the "bling"! :tu