Varnish for wooden scales?

[trondsi]

Hi everyone! I have a razor where the varnish looks a bit uneven (shiny and matte in different spots). I suspect that the razor was packaged before the original varnish was completely dry.
Do you guys have a favorite translucent varnish to make wooden scales nice and shiny? (or semi-shiny)

[gssixgun]

A wipe on Polyurethane is one of the easiest there is to use, quite durable too

[JRM]

For nice, shiny scales, I use clear lacquer. I just put a metal rod through the pivot hole and dunk the entire scales into the lacquer can and let it drip dry, carefully turning it until it stops running. Gives a beautiful "wet" look to the scales.

[Giggitoni]

Some use “super glue” with good results; glossy, hard, waterproof.

[Gasman]

Tru-oil Gun Stock finisher works nice too. But its a lot of work.

[PaulFLUS]

I use a brush on poly. It leaves a really nice finish but it takes some practice to get it right. I usually put a coat and sand to opaque a couple of times then put a very thin coat of some thinned about a quarter to finish. Hard to get it thinned properly without getting bubbles but if your patient stirring it works well.

[outback]

My preference is "True-Oil"

It really makes the wood come to life, compared to others. It is time consuming building the layers, once the grain is filled.

But the results are worth it.





Being a gun stock finish, it'll handle anything you can throw at it.

Super glue tends to crack from the scales flexing, from what I've seen from those I've done.

[PaulFLUS]

Tru oil does leave a nice finish but if the wood is very dense and hard it won't penetrate, at least on that southern live oak heart wood. That stuff is the hardest, densest wood I've ever worked with. For that I use gun stock wax and leave it in the sun for about 10-12 coats

[stoneandstrop]

Minwax wipe on Poly is foolproof and pretty durable.
Lacquer in a spray can works well too and each coat of lacquer melts into the last creating one thick coat essentially.
Shellac does the same thing melting into previous coats. (not durable though)
Urethane/varnish and polyurethanes adhere between coats but do not melt into the previous layer to become one.
Polyurethanes being the most durable of this group.

[CrescentCityRazors]

I like superglue. First coat thin, don't sand. Second coat thick, sand lightly with 1k, then buff with basically any fine buffing compound and a scrap of old tshirt. Start doing thin coats, buffing only, until you get the depth effect you want. Two part epoxy or polyester casting resin can be absolutely stunning when you really nail it. You need some sort of motorized apparatus for turning it, though, so you don't get runs. I have used double boiled linseed oil, too, but it takes weeks to apply and age the two or three coats you want. Tung oil is good on some woods, like ebony or walnut. These oils oxidize and for best effect they need to age a bit before buffing and handling. A simple polyurethane varnish is the painless way, or some good shellac or clear lacquer. Krylon clear actually works surprisingly good. Spray it on LIGHTLY, then a couple more light coats a day apart in a completely dust free environment, Buff with clean cotton tshirt between coats and lightly with a clean cotton wheel at low speed, at the end, after curing for 3 or 4 days. More than one way to gitter done. When you make wood scales, don't make one pair. Make three. Try stuff. Toss them when you screw up and don't let it mess up your digestion. A common mistake is overbuffing the finish on a wheel. You WILL do that at least once. It is a given. Another is not knocking down the lint and bubbles in a coat before applying the next. Another is letting drips and runs solidify, which are surprisingly difficult to sand smooth without trashing the whole thing and having to start all over. That is one advantage of wax type finishes, is that they don't completely solidify and simple rubbing brings the luster back, and you can reapply any time you think you would like to.