Results 1 to 10 of 11
Thread: lapping problems
Hybrid View
-
04-28-2010, 12:09 AM #1
-
The Following User Says Thank You to BladeRunner001 For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 12:22 AM #2
- Join Date
- Jan 2010
- Location
- Portland, Or
- Posts
- 15
Thanked: 1When lapping your 12k try using a ball point pen to put your grid lines on with. I did the same thing with a pencil and discovered that as soon as you work up a slurry the pencil lines will come right off even if you are not against the lapping stone. After I drew the grid on with a pen it took me about 2 hours to actually get the 12k stone flat.
-
The Following User Says Thank You to jeb For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 12:33 AM #3
If you're using a soft pencil the lines will rub off in the slurry right away. Pen seems ok, but I have never used it so I wouldn't know. The DMT 325 is a good lapping stone.
-
The Following User Says Thank You to Disburden For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 02:01 AM #4
IME lapping on a 325 or a 120 DMT in the kitchen sink with the water gently washing the swarf away is a good method to avoid a build up of slurry that will give you false readings on your grid or cause stiction. YMMV.
Be careful how you treat people on your way up, you may meet them again on your way back down.
-
The Following 2 Users Say Thank You to JimmyHAD For This Useful Post:
Disburden (04-28-2010), shortmoneyshave (04-30-2010)
-
04-28-2010, 02:33 AM #5
-
The Following User Says Thank You to Disburden For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 07:40 AM #6
shortmoneyshave,
I used all sorts of methods for hone flattening until I finally gave in and got a DMT 325 continuous diamond plate.
Flattening the hones is now so much easier, quicker and cleaner than before
Highly recommended
Have fun !
best regards
Russ
-
The Following User Says Thank You to PhatMan For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 09:05 AM #7
+1 for the 325 DMT. Thats a great stone, very useful for lapping, and you can also use it for major edge repair if you need to.
-
The Following User Says Thank You to Stubear For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-28-2010, 11:40 AM #8
Lap your Norton on some 220 wet/dry sand paper. Rotate the Norton lap around several times through the process. When lapping you hones also rotate the hone around from time to time and also the lap. If your Norton lap is flat within reason your results on the hones should be just as good. Rotating them while lapping will improve the results. Flat is a relative term. DMT's may give better flatness if rinsed while lapping. With the Norton, I don't rinse very often and allow the slurry built up on the lap to assist in the lapping process. Rinse when the groves in the lap are close to full with slurry. That works best for me.
“If you always do what you always did, you will always get what you always got.” (A. Einstein)
-
The Following User Says Thank You to Joed For This Useful Post:
shortmoneyshave (04-30-2010)
-
04-30-2010, 02:19 AM #9
- Join Date
- Mar 2010
- Posts
- 11
Thanked: 03m wet sanding
I picked up some 3M wet/dry grit sandpaper and a 80 grit emery sheet. Lapped the nortons on 80,220,+320, did a great job of flattening. The chinese 12k will need a little more work. After a couple of hours of lapping stones, I put it down for the day. Thanks for all the helpful advice.
-
04-30-2010, 09:31 PM #10
- Join Date
- May 2005
- Location
- Saint Paul, Minnesota, United States
- Posts
- 7,974
- Blog Entries
- 1
Thanked: 22043M wet/dry is what I use...just keep it wet.
Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin
-
The Following User Says Thank You to randydance062449 For This Useful Post:
shortmoneyshave (05-01-2010)