Page 1 of 2 12 LastLast
Results 1 to 10 of 17
Like Tree1Likes

Thread: Honing a micro bevel without tape.

  1. #1
    Senior Member
    Join Date
    Jan 2008
    Location
    Northern California
    Posts
    1,301
    Thanked: 267

    Default Honing a micro bevel without tape.

    I propose that it is possible to put a micro bevel on an edge without tape and the procedure would go something like this.

    I have an Asagi that I have been using and I have always been one to use a magnifier to look at my edges. It may be that this is common knowledge with a lot of you but I have not read anything about it. Recently I have been experimenting with the following;

    I am using a heavy slurry on my stone using a certain amount of pressure on the edge....let us call it X. (I have actually used X pressure all the way up the progression). I then go to water with just a little slurry and I lighten up on the pressure so that the edge just barely comes in contact with the stone. When I look at the edge using a 30X scope I see that about the last 25% of the bevel is polished to a higher level than further up the bevel.

    If my conclusions are correct when I was using the higher pressure X I was deforming the blade every so slightly and establishing a bevel that was at a slightly flatter angle than when I went to my final polishing using pressure that was a fraction of X, thus the little band along the edge that was different than the rest of the bevel. I have seen this when I was doing micro bevels using a 30K and films.

    Am I all wet? I have been getting edges that rival any I have ever used before, even 0.1 micron films.


    Just a thought,
    Richard

  2. #2
    Know thyself holli4pirating's Avatar
    Join Date
    Feb 2008
    Location
    New York
    Posts
    11,930
    Thanked: 2559

    Default

    Using pressure and then honing without pressure will create a double bevel. It's because the pressure makes the blade flex, which changes the honing angle to make it less than normal. Then when you release the pressure, the honing angle returns to normal, and that creates the second bevel.

    I guess using pressure would be like negative tape, and no pressure is like no tape. It is the same effect as if you started without tape and then added it.

    This is just as you described it.

    Creating a double bevel helps you overcome any issues you may have had with a non-perfect bevel in the first place, because the second bevel is just on the very edge of the razor. In creating that second bevel, you remove any inconsistencies from the primary bevel. But if you set your primary bevel properly and do everything from thereon up properly, the end result will be the same with a single or double bevel.
    Last edited by holli4pirating; 10-08-2010 at 02:16 AM.

  3. The Following User Says Thank You to holli4pirating For This Useful Post:

    riooso (10-08-2010)

  4. #3
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    I don't buy it. Altering the pressure is only going to alter the contact if you are causing a flexing of the blade with the higher pressure, which will cause the very edge to lift off of the hone.

  5. #4
    Senior Member blabbermouth hi_bud_gl's Avatar
    Join Date
    Nov 2005
    Posts
    4,521
    Thanked: 1636

    Default

    if you have quality blade you don't need to have double bevel etc.
    it is all illusion that double bevel is sharper etc.
    double bevel or taping of the spine in last stage of honing will help you only if your blades quality is low and adding 1 layer gives a little more support to the edge which doesn't brake down.
    hope this helps.
    gl

  6. The Following 2 Users Say Thank You to hi_bud_gl For This Useful Post:

    Disburden (10-23-2010), riooso (10-08-2010)

  7. #5
    BHAD cured Sticky's Avatar
    Join Date
    Jan 2008
    Location
    Indiana
    Posts
    1,306
    Thanked: 230

    Default

    I agree that the edge deforms while honing with slight pressure, on the more hollow grinds. While the fuller wedges, IMO, will deform very little; if at all. You can lean the side of a singing hollow's edge into your fingernail and see the deformation easily, with light pressure.

  8. #6
    They call me Mr Bear. Stubear's Avatar
    Join Date
    Jul 2009
    Location
    Alton, UK
    Posts
    5,715
    Thanked: 1683
    Blog Entries
    3

    Default

    Arguably that could work with a hollow ground as they do flex (although you will add more wear than necessary to the blade by using the extra pressure), but I agree with Sticky about the more wedge like razors; Due to the stiffer blades that wont work so well.

  9. #7
    Senior Member Lesslemming's Avatar
    Join Date
    Jun 2009
    Location
    Germany
    Posts
    554
    Thanked: 197

    Default

    The one thing that occurs to me much more often than a double bevel when using pressure is that the very edge crumbles down.
    So even if it is possible to "flex" the bevel with pressure I wouldnīt do it
    because of the damage done to the edge using pressure


    btw. I often get a double-bevelish look (that is a bevel that is hazy on the back and more polished towards the edge)
    when I use my nakayama with slurry and diluting or finishing on water (patiently, as it takes a lot of time).
    I donīt think this has much to do with pressure but with the slow Nakayama trying to polish away the hazy look,
    but is unable to get past thefirst third of the bevel.
    Last edited by Lesslemming; 10-08-2010 at 09:08 AM.

  10. #8
    Member AFDavis11's Avatar
    Join Date
    May 2005
    Location
    Virginia
    Posts
    5,726
    Thanked: 1486

    Default

    This honing technique was used and advocated by Bill Ellis, about 4 years ago I think. He removed the post and the accompanying graphics though.

    Although he used this method in practice, his theory was that the mid-bevel needed to be thinned tighter than the bevel edge.

    I have used varying pressure in honing but I don't know for sure what it does.

  11. #9
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    If I was going to go for a double bevel I would use tape. Tim Zowada had, and maybe still has, his method on his website. This involved beginning with one layer and continuing with that until the end when you go to 3 layers to do the double bevel. It is worth noting that Tim posted that he was giving up the double bevel. He said he was going to update the site to reflect that but I haven't checked nor has he posted on it since then AFAIK.

    The problem I would expect with doing a double bevel using alternate pressure rather than tape would be inconsistency. Maintaining consistent pressure throughout the stroke would be very difficult IMO. The difference in stiffness of individual blades would come into play as well. OTOH, I don't care for double bevels so it isn't an issue for me.
    Be careful how you treat people on your way up, you may meet them again on your way back down.

  12. #10
    Modine MODINE's Avatar
    Join Date
    Dec 2009
    Location
    Lee's Summit, Missouri- (KC)
    Posts
    1,442
    Thanked: 730

    Default

    Richard;

    The J-nat slurry particles keep getting finer and finer when you use it. The same thing happens with the Escher. I understand the blade deflection theory, but we would have seen that present itself at lower grits. My 2cents.

    Mike

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •