Page 1 of 2 12 LastLast
Results 1 to 10 of 20
Like Tree1Likes

Thread: Honing razor with wide bevel..

  1. #1
    GO HABS GO!
    Join Date
    Nov 2008
    Location
    New Brunswick, Canada
    Posts
    930
    Thanked: 398

    Default Honing razor with wide bevel..

    Hey guys,

    Do you guys have any suggestions on how to tackle a razor with a fairly wide bevel?

    Thanks!

    JF

  2. #2
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    You hone it the same as any other. If for some reason you consider it to be problematic, you could tape the spine and that would cut a slightly narrower bevel.

    Is your concern aesthetic or functional?

  3. The Following User Says Thank You to Utopian For This Useful Post:

    Dups (10-22-2010)

  4. #3
    GO HABS GO!
    Join Date
    Nov 2008
    Location
    New Brunswick, Canada
    Posts
    930
    Thanked: 398

    Default

    More of a functional issue.

  5. #4
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    Okay, so did you create the wide bevel or did you find it that way?

    The width of the bevel is entirely a function of geometry. It is produced by the amount of steel required to be removed in order to establish a straight line between the very edge of the blade and the spine. Bevel setting is the elimination of all steel needed to convert a "U" shaped cross section of the edge into a "V" shape. So the bevel width is a function of the grind of the razor and the thickness of the spine. A thicker region of steel near the edge will result in a wider bevel. A worn spine will also lead to a wider bevel.

  6. The Following User Says Thank You to Utopian For This Useful Post:

    Dups (10-22-2010)

  7. #5
    GO HABS GO!
    Join Date
    Nov 2008
    Location
    New Brunswick, Canada
    Posts
    930
    Thanked: 398

    Default

    The razor was bought new with a factory set wide bevel. I've managed to set the bevel myself, but I find that it lacks behind in sharpness when I reach the refining stage.

  8. #6
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Are you still working on this same razor?????

    http://straightrazorpalace.com/advan...g-ti-c135.html

  9. The Following User Says Thank You to gssixgun For This Useful Post:

    Disburden (10-22-2010)

  10. #7
    GO HABS GO!
    Join Date
    Nov 2008
    Location
    New Brunswick, Canada
    Posts
    930
    Thanked: 398

    Default

    Hehe yep! I got it fairly close to shave ready using Bart's Unicot method, but It's still not where I'd like it to be.

  11. #8
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    Has the bevel noticeably widened from the time you began to hone it to now?

  12. #9
    GO HABS GO!
    Join Date
    Nov 2008
    Location
    New Brunswick, Canada
    Posts
    930
    Thanked: 398

    Default

    Not much. Maybe a little, but not significantly more. I dulled the razor on the bottom of a glass and went to town on the coticule with slurry until the razor was shaving arm hair all across the blade. The next step is where is sort of went down hill. I don't know if I'm doing too many or not enough passes with the diluted slurry.

  13. #10
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    I'm sorry, I'm not criticizing the method, but I have never understood the point in pre-dulling the razor. I suppose I might if I didn't use a microscope to assess my bevel progression.

    Regardless, you're going to have to assess whether or not you've got the bevel set. That's the hallmark, critical, make it or break it, here we go decision point. Aside from geometry, the bevel would also widen if you are using so much pressure that you're flexing the blade. If the bevel is set, you need to lighten up on the pressure and move on up the progression, even if that progression is just along one of the coticule paths. If the bevel is not set, then you might want to put on a layer of tape or two to finish it.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •