Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Senior Member Dllandry's Avatar
    Join Date
    Dec 2009
    Location
    Toronto On M1N 3G1
    Posts
    672
    Thanked: 233

    Default 3-Piece Sharpening Set

    Item # 360226823337


    Bought this on ebay and just wanted to know if they are decent stones to hone a razor on?

    This is a new Chinese Hone or waterstone, used for final polishing of open razors and similar items like woodworking tools.
    It is approximately 12,000 grit size.
    The stone comes from the Guangxi province of China.

    It measures 150 mm x 50 mm x 17 mm in depth . Stones are cut by hand, dimensions may vary slightly.
    Stones are carefully selected and cut but due to their natural origin differences in visual appearance might occur.
    Any such differences do not impair the stone function in any way.


    It is an extremely fine stone and apart from being lapped flat and the edges chamfered it is unused (if you buy elsewhere it will not be lapped and chamfered - beware that although some people say that the stone needs flattening, it most certainly does need flattening - this has already been done for you!).

    It is very hard - almost like ceramic, and it gives a really fine polished edge.
    It is a slow stone, requiring 50 - 100 laps to polish the edge of a straight razor, but the results are superior smoothness - sometimes likened to a "buttery" feel.





    8000 GRIT
    Perfect for the blade’s smooth finish touch.
    The 8000 grain will allow you to polish the edge with a mirror effect and a slippery cutting.

    Only water is needed to lubricate the cutting edge
    Size: 180x60x16 mm

    The 5000 grit is a unique sharpening stone.

    Although it's fine grit, it is designed to cut-not polish.
    It leaves a refined edge that can be brought to a mirror finish quickly on the 8000 grit stone.
    Use the 5000 grit stone before the final polishing, for a more consistent, longer lasting edge.

    Only water is needed to lubricate the cutting edge

  2. #2
    Senior Member blabbermouth niftyshaving's Avatar
    Join Date
    Oct 2009
    Location
    Silicon Valley, CA, USA
    Posts
    3,157
    Thanked: 852

    Default

    The grit numbers are good.
    The Chinese Guangxi (often called the C12K here) stone is reported to be
    slow so experiment -- sneak up to nearly 100 laps by some reports.

  3. #3
    Large Member ben.mid's Avatar
    Join Date
    Aug 2008
    Location
    Oxfordshire, England
    Posts
    3,096
    Thanked: 763

    Default

    Probably the same as these that Sham was trying to identify, plus the Chinese. As mentioned, the Ch is slow. Slurry on it will speed things up considerably though.

    Should be a good set up till the HAD gets you!

  4. #4
    Carbon-steel-aholic DwarvenChef's Avatar
    Join Date
    Mar 2007
    Location
    Santa Barbara, CA
    Posts
    2,814
    Thanked: 823

    Default

    Ya HAD is next... I've moved on to JHAD, Japanese Hone AD... why is my wallet running away in terror???

  5. #5
    Senior Member Croaker's Avatar
    Join Date
    Feb 2008
    Location
    Arizona
    Posts
    1,360
    Thanked: 376

    Default

    You're done, son. Start figuring out storage for the coming rocks, because they take up quite a bit of space. The Chinese is a good start; I got good results from mine for months before moving up to an Escher due to a lucky antique store find. The Chinese gives a good smooth final edge, as long as the bevel is properly set and initially sharpened. That is where all the other stones come in! Have fun.

  6. #6
    Senior Member Dllandry's Avatar
    Join Date
    Dec 2009
    Location
    Toronto On M1N 3G1
    Posts
    672
    Thanked: 233

    Default

    Thans to everyone on the posts I think I well on the way to spending way more than is considered sane, but as the wife said it could be worse.

  7. #7
    Senior Member blabbermouth hi_bud_gl's Avatar
    Join Date
    Nov 2005
    Posts
    4,521
    Thanked: 1636

    Default

    You will need some extra stone between 8k and chin12. That 8k is not as fine as norton8k etc.
    will take you long time get edge from this 8k to 12k level.
    if you can add 10 NANIWA you should be ok .
    hope this helps.
    Last edited by hi_bud_gl; 05-15-2010 at 07:40 PM.

  8. #8
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    Sham,
    tested the hones and I think liked them.
    The 12k Chinese is the standard poor man's choice for a finisher.
    Stefan

  9. #9
    Senior Member Dllandry's Avatar
    Join Date
    Dec 2009
    Location
    Toronto On M1N 3G1
    Posts
    672
    Thanked: 233

    Default

    Oh god you mean I will end up spend even more on hones... this is gonna be a way expensive hobby isnt it.

  10. #10
    I used Nakayamas for my house mainaman's Avatar
    Join Date
    Aug 2009
    Location
    Des Moines
    Posts
    8,664
    Thanked: 2591
    Blog Entries
    1

    Default

    Quote Originally Posted by Dllandry View Post
    Oh god you mean I will end up spend even more on hones... this is gonna be a way expensive hobby isnt it.
    well if you want to find stones that give you edge you like it can be expensive. The prefinisher line up is fairly easy to figure out, naniwa super stones 1k3 or 5k, 8k. Finisher stone is where things get complicated, the popular options are:
    Cheapest - chinese 12k
    Reasonably priced:Naniwa Superstone 12k
    A bit on the expensive side: Shapton 16k

    Expensive:
    Shapton 30k
    Natual finishing stones

    I am might be missing some stones in the list, also its relative what is cheap and what is expensive.

    Really my advise learn stropping , then send your blades to be professionally honed, and only do touch ups with pastes and /or hi grit synthetic when needed. I think this can be most cost effective, because with good stropping you can use a bunch of edges for quite some time before they need to be honed again.
    Stefan

  11. The Following 2 Users Say Thank You to mainaman For This Useful Post:

    Dllandry (05-15-2010), niftyshaving (05-16-2010)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •