Results 1 to 10 of 16
Thread: New to it all...
-
04-29-2014, 04:41 PM #1
- Join Date
- Apr 2014
- Location
- Alabama
- Posts
- 5
Thanked: 0New to it all...
Hello.
I wanted to make my entrace to the forum and club of straight razor shaving.
I have been looking into taking the plunge for a long time and recently purchased a Theirs-Issard razor when I was away on a trip. I am facinated by the art that is shaving outside of my old typical ways of turning on the electric razor or using an old mach 3 that's under the sink. I shave almost everyday, due to the military and my significant other...but honestly, I can't grow a good beard anyhow! haha.
I am really open to hear from veteran suggestions as far as techniques and things of that nature...I have really thick facial hair and anything to help make the whole process a much smoother one is nice to know. Also, I got a strop with my razor and it was recently chewed up by one of the pups, and I have a big background in wood working and some leather stamping...was thinking about making my own? Any advice would be nice there too.
- Tee
-
04-29-2014, 05:04 PM #2
Welcome to the SRP forum!!!
-
The Following User Says Thank You to HaiKarate For This Useful Post:
TeeZeeMee (04-29-2014)
-
04-29-2014, 06:58 PM #3
Hi and welcome. Check out the library for all the starter info and the other basics of Sr shaving. Tandy is recommended regularly for leather. Good luck
My wife calls me.........Can you just use Ed
-
The Following User Says Thank You to eddy79 For This Useful Post:
TeeZeeMee (05-01-2014)
-
04-29-2014, 08:21 PM #4
Hi, and welcome to the SRP family !! Like eddy79 said check out the forum's library, ask a lot of questions because there are members with a wealth of knowledge that are very willing to share, Just take your time so you enjoy the journey!!
-
The Following User Says Thank You to Walterbowens For This Useful Post:
TeeZeeMee (05-01-2014)
-
04-29-2014, 08:35 PM #5
Welcome to the forum! This is definitely the place if you have projects in mind. Search around to see what others have done in making homemade strops. You are sure to find a wealth of information. Good luck!
--Mark
-
The Following User Says Thank You to Speedster For This Useful Post:
TeeZeeMee (05-01-2014)
-
04-29-2014, 09:54 PM #6
Welcome TeeZeeMee! In case you have not seen it yet, start here:
Beginner's guide to straight razor shaving - Straight Razor Place Library
For your other questions just type in "Scale Making" or "Strop Making" into the Search Engine and get ready for information overload!Watch plenty of Videos and then post in the various Sub/Specialty Forums when you are ready for more details!
Enjoy the journey... And, if what others have reported that initially had difficulty with beard growth, once you have some time in SR Shaving you may notice your hair follicles operating on an entirely different level!
Shawn
-----
-
The Following User Says Thank You to Prahston For This Useful Post:
TeeZeeMee (05-01-2014)
-
04-30-2014, 03:44 AM #7
Haya TeeZeeMee, welcome to the site
Best advice is don't start a drinking session and say "hey guys guess what I can do" then try to shave - it will end in tears
Beyond that reading up is part of the fun to start with.A good lather is half the shave.
William Hone
-
The Following User Says Thank You to Crackers For This Useful Post:
TeeZeeMee (05-01-2014)
-
05-01-2014, 12:52 PM #8
- Join Date
- Apr 2014
- Location
- Alabama
- Posts
- 5
Thanked: 0Thanks everyone for the warm reception!
I will let y'all know what my first attempt at making a strop turns out to be!
-
05-01-2014, 01:12 PM #9
My homemade strop is a 3" wide strip of roo leather that i sanded smooth, then fixed a hinge over either end of as a stiffener, put a picture hanging loop thingo on one end to attach a piece of strig/clip too, and a d ring made from bent wire to the other end as a handle and away i went.
I am sure you could make something prettier though.Bread and water can so easily become tea and toast
-
The Following User Says Thank You to edhewitt For This Useful Post:
TeeZeeMee (05-01-2014)
-
05-01-2014, 03:53 PM #10
- Join Date
- Apr 2014
- Location
- Alabama
- Posts
- 5
Thanked: 0Thanks for the heads up!
I think I am gonna use some of my carpentry skills to help with the process, and make it somewhat unique and ergonomically friendly for me.