Results 1 to 10 of 24
Thread: Rust on Dovo
-
10-08-2008, 05:27 AM #1
- Join Date
- Jul 2008
- Posts
- 6
Thanked: 0Rust on Dovo
I recently (w/in 3 months) purchased a new DOVO razor and I have noticed that it is already starting to rust.
I keep it in a dry place, and dry it off when I am done using it, has anyone else had a problem with razors rusting quickly? Or are their any tips for keeping your blades from rusting?
I already have some naval jelly so I was going to give that a shot to remove the current rust, but would like to prevent this from happening again so any pointers would be appreciated.
-Mark
-
10-08-2008, 12:47 PM #2
- Join Date
- Oct 2008
- Location
- Sawbridgeworth, UK
- Posts
- 6
Thanked: 0Rust only occurs when metal oxidises with moisture, so perhaps the room in your house where you store it isn't as moisture-free as you think? Either that or the metal on the blade is contaminated?
-
10-08-2008, 12:53 PM #3
- Join Date
- Apr 2007
- Location
- St. Paul, MN, USA
- Posts
- 2,401
Thanked: 335Make sure it is dry before you put it away and store it in a dry environment. Ensure the inside surfaces of the scales are also dry. Before putting my razor away I rinse the blade in the hottest water my bathroom faucet can produce. Then I wipe it dry on a towel, run a corner of the towel between the scales, and close the razor only enough to cover the edge of the blade as I don't want contact between the blade and scales until I know all the parts are completely dry. The next day I close up the blade if I'm not going to use that razor for the morning's shave. I don't oil the blades of any razors in rotation and have had no issues with corrosion on any of my razors.
Dry is good...Last edited by Bruce; 10-08-2008 at 12:56 PM.
-
10-08-2008, 01:17 PM #4
- Join Date
- Jan 2008
- Location
- Northern California
- Posts
- 1,301
Thanked: 267I put a little oil on toilet paper and wipe my razor after every use. I too, have had problems and the only way that I can make sure that it does not happen is to oil it. I did not get rust but the black spots which is the beginning of the process from what I can tell. I use Corrosion-X only because that is what I have handy but I have read that there are better treatments available.
Take Care,
Richard
-
10-08-2008, 01:52 PM #5
WhoA!
Hold off on that Naval Jelly. That might be like using an elephant gun to hunt a rabbit.
How bad is the rust exactly? Are we talking a few pin-heads spots? Perhaps dark spots?
These might be water spots. Also, I've noticed that for some reason (be it water hard/softness, shave soap ingredients, metal composition of the blade, etc) I have some razors that develop small brown spots on the blade. I can buff them out, but right after the next shave, or even during, these small spots appear. Over the years I have noticed that they had not appeared when I shaved with the razor at different living locations...so I'm thinking it has something to do with a combination of the issues I listed above.
Another possible issue would be small black/grey spots. These are water spots, from water that was either not wiped away from the last shave, or was between the scales (when you closed the blade it came in contact with these spots).
What ever the case, I would not recomment Naval Jelly to remove the rust. If you have a metal polish (Maas works great, flitz works too), I'd put some on a QTip or tissue and rub off the area. If it's bad enough, I'd then try a dremel, but be careful with that if you are not familiar. It's easy to chip out a blade if you are not careful.
Naval Jelly should be employed for heavy duty rust. Rust that you have scrapped the bulk of it away, and need to get into the deep pitting to take care of...then move on to the Maas polish.
If it's just water stains, you might even be able to get away with a 'poor mans polish' and use a little toothpaste to remove it (toothpaste does have a grit to it...)
Anyway, I'd hold off on extreme measures for now....
Are you able to post a picture of the 'rust'? If you have a digital camera, put it on Macro, shut off the flash and under good lighting take a close up picture of the area and post it here. This would help pin-point the problem/cure a little better.
C utz
-
10-08-2008, 04:16 PM #6
I always rinse my razors under the Hot tap after its been running a while,Then I wipe it with a towel & finish off by wiping it with a piece of folded up tiolet tissue.I fold this around the spine & are very careful about the edge of the blade.The blade feels warm to the touch after this .& finally I strop it lightly a few times on the canvas side of my strop.also My Razors are stored away from the miost air of the bathroom . Since iv'e been doing this I've had no problems with rust or my blades loosing thier edge prematurely. Paul
-
10-08-2008, 05:13 PM #7
I'm having the same problem. I think Dovo has a Quality Control problem or released a bad batch. If you read all the threads lately you will find a lot of Dovo issues...which is strange because I've always considered them great razors.
In my case I aquired a brand new unopened box Dovo, honed it up, and put it in my rotation. I didn't treat it any different than my other razors but within a couple weeks I started noticing water spots so I hit it with some Flitz. After a little over a month it started showing symptoms of pitting. I don't think the final polish on this razor was done correctly as there is no way it should start pitting after just a month.
With a new Dovo I would suggest oiling it before putting it away...at least every other time. I'm selling mine and looking for an older one.
-
10-08-2008, 05:47 PM #8
Any carbon steel razor is subject to rusting if not protected with some sort of rust preventative. I use an Outer's Silicone Gun Cloth impregnated with R.I.G. (rust inhibiting grease). Unfortunately it appears that R.I.G. may be discontinued. A google search didn't reveal any current source for it. Glad I bought a large container. Some forum members favor Camellia oil as a rust preventative. To remove any surface rust I would suggest Semi-Chrome or Flitz.
Be careful how you treat people on your way up, you may meet them again on your way back down.
-
10-08-2008, 10:43 PM #9
Check to see if there is any razors in the area of the Dovo razor you are talking about that have celluloid scales....of if the Dovo itself has celluloid scales. If there is any degradation of the celluloid it would cause an accelerated rust/pitting on the blade.
I've had a dubl duck Satinbaby (clear celluloid scales) break down on me, and take out not only the dubl duck but the razors on either side of it. The rusting looks like a haze pattern of rusting...
C utz
-
10-09-2008, 12:21 AM #10