Results 1 to 10 of 11

Hybrid View

kimo Butcherd on the Hone?... 11-24-2006, 12:12 AM
FiReSTaRT Probably the grinder or the... 11-24-2006, 12:41 AM
jscott quite alot of hone wear on... 11-24-2006, 12:54 AM
randydance062449 My first reaction was "WHY... 11-24-2006, 01:05 AM
rtaylor61 Randy, I also like a... 11-24-2006, 01:12 AM
  1. #1
    Member kimo's Avatar
    Join Date
    Oct 2006
    Location
    CA
    Posts
    59
    Thanked: 2

    Default Butcherd on the Hone? Butchered on the Strop? Just Butchered?

    I have been trying to hone a Wade and Butcher I picked up on Ebay. Whoever had it before me tried to do some strange type of honing and I'm trying to over come that.

    I hope I am not fighting a lost cause.

    Here are some pics of sides A and B. Maybe you masters can tell me whats up.

    I nearly have my double duck to shavable and am working on another W&B, which by the way, seem to have a wedge grind or more straight sides.

    I also have a Keystone (anyone ever heard of it?) which I have been working on. So far, only the double duck and the keystone have been any where near smooth shaving sharp.






  2. #2
    Loudmouth FiReSTaRT's Avatar
    Join Date
    Jun 2005
    Location
    Etobicoke, ON
    Posts
    7,171
    Thanked: 64

    Default

    Probably the grinder or the Dremel sharpening attachment.

  3. #3
    Senior Member jscott's Avatar
    Join Date
    Jul 2006
    Location
    New York City
    Posts
    392
    Thanked: 6

    Default

    quite alot of hone wear on that baby.

    in the first 2 pictures you can see how wide the bevel is in the middle of the razor compared to either end...then look at the spine in the middle and that is also shows much more hone wear. i'd say someone use alot of pressure in that area when honing. a wide bevel in and of itself doesn't mean anything bad, but yours shows excessive/uneven pressure in the middle.

    maybe you can get it to be a good shaver...but it just may be too much of a lost cause. definite regrinding would be good but that prolly cost you more then you paid for the blade.

    bummer-ooo

    ~J

  4. #4
    Hones & Honing randydance062449's Avatar
    Join Date
    May 2005
    Location
    Saint Paul, Minnesota, United States
    Posts
    8,023
    Thanked: 2209
    Blog Entries
    1

    Default

    My first reaction was "WHY BOTHER?" but then I remembered how I liked a challenge. So....

    1. Use 1000 grit sandpaper, wet/dry, and lay it over your hone or on some flat surface.

    2. Hone with out tape on the spine until you have a bevel on the edge for the full length of the blade. Use about 2 lbs of pressure.

    3. Use the X pattern

    4. Tape the spine and go to the 4k until it passes the thumbnail test.

    5. Start a pyramid at the 15/5 level.

    Hope this helps,
    Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin

  5. #5
    Senior Member blabbermouth rtaylor61's Avatar
    Join Date
    Jul 2005
    Location
    Salt Lake City, Utah
    Posts
    2,376
    Thanked: 2

    Default

    Randy,

    I also like a challenge. For me, I would do it a bit differently:

    1. Get padded envelope
    2. Address to Bill Ellis
    3. Toss in some money
    4. Go stand in line at the post office (okay, that's the challenge this time of year)
    5. Wait for return

    No, I'm not lazy. I'm like George Bush. I'm edumacated!

    RT

  6. #6
    Knife & Razor Maker Joe Chandler's Avatar
    Join Date
    Feb 2006
    Location
    Louisiana
    Posts
    1,849
    Thanked: 50

    Default

    I believe that one could be reground, and would have to be, IMO, to be usable again.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •