Page 1 of 3 123 LastLast
Results 1 to 10 of 25
Like Tree69Likes

Thread: 1820's Greaves for comission.

  1. #1
    Captain ARAD. Voidmonster's Avatar
    Join Date
    May 2011
    Location
    Pacifica, CA
    Posts
    2,474
    Thanked: 2226

    Default 1820's Greaves for comission.

    The first restoration I've done for someone that's not me.





    I did some minor blade and scale cleanup before I took these pictures. The scales were really in good shape, though they had a fair bit of grunge on them, as most razors do when they're almost 200 years old.

    My goal was to find a pleasing balance between visible wear and clean & usable. Basically, I wanted to turn up the contrast. Make the clean parts cleaner and the rough parts sturdier.

    To that end, the first step was getting it apart without damaging any of the original bits.



    The steel support collar there with the missing piece was like that to begin with -- those support washers were never made for looks! You can see that the steel collars from the point have a lot less oxidation on them because they were kept away from water.

    If you right click and zoom in, you can see that the pivot pin got chewed up by the nail-hole in the tang.

    To get the collars off cleanly, I used a tiny Dremel burr designed for engraving to carefully make a center divot as a guide, then used the drill press and a 1/16th bit to drill down to below the level of the washers. Then I stuck that burr tool down in there and very slowly, gently worked it around until the collar came off.

    Neat and tidy!

    From there it was a whole lot of hand-sanding and buffing. I've grown to really like the buffer, providing I only use it for the final polish. But getting that polish took a lot of the dark out of the stamps, and I wanted the tang and spine to look a lot less shiny and 'clean' than the blade. So I masked off all the shiny parts and used a combination of Dremel 320 grit puffs, then gun bluing, then naval jelly. The end result is a much more matte-finish spine and tang with nice, dark letters.

    The blade face was just a hand-sanding progression with a final round of polishing compound on the buffer.

    For the scales, I used a lacquer-based India ink and CA glue to fill the one void and tiny crack, then sanded the worst of the surface delamination off and gave it all a high gloss with the buffer.

    And here's the end result. Other than the pin stock and the thrust washers (which you cannot see), it's all original!



    (And yes, lurking under the years of grime was a lovely bit of streaked black horn. I'm pretty sure the original scale treatment dyed them solid black, but I thought the streak looked awesome.)

    -Zak Jarvis. Writer. Artist. Bon vivant.

  2. The Following 4 Users Say Thank You to Voidmonster For This Useful Post:

    Blistersteel (08-18-2014), carrolljc (08-17-2014), Geezer (08-16-2014), Trimmy72 (08-17-2014)

  3. #2
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,383
    Thanked: 4820

    Default

    Nice job, I have no doubt as to why you were chosen for this job.
    Voidmonster likes this.
    It's not what you know, it's who you take fishing!

  4. The Following User Says Thank You to RezDog For This Useful Post:

    Voidmonster (08-16-2014)

  5. #3
    lz6
    lz6 is offline
    Senior Moderator lz6's Avatar
    Join Date
    Feb 2010
    Location
    California
    Posts
    4,833
    Thanked: 1841

    Default

    Sweet restore. The owner is going to be proud of that beauty.
    Voidmonster likes this.
    Bob

    "God is a Havana smoker. I have seen his gray clouds" Gainsburg

  6. The Following User Says Thank You to lz6 For This Useful Post:

    Voidmonster (08-16-2014)

  7. #4
    Senior Member blabbermouth edhewitt's Avatar
    Join Date
    May 2013
    Location
    Perth Australia
    Posts
    7,741
    Thanked: 713
    Blog Entries
    1

    Default

    Good work zac, that is what a restore should be.
    Voidmonster likes this.
    Bread and water can so easily become tea and toast

  8. The Following User Says Thank You to edhewitt For This Useful Post:

    Voidmonster (08-16-2014)

  9. #5
    Senior Member blabbermouth Substance's Avatar
    Join Date
    Jun 2013
    Location
    Gladstone QLD AUSTRALIA
    Posts
    3,245
    Thanked: 804

    Default

    Nice restore someone gonna be happy
    Voidmonster likes this.
    Saved,
    to shave another day.

  10. The Following User Says Thank You to Substance For This Useful Post:

    Voidmonster (08-16-2014)

  11. #6
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Thanks Zak. Aside from the as expected, beautiful job, I really appreciate your going through the steps you took in the restore. Not that I'd ever try such a job, but I'm sure many members here who are so inclined will learn from your post.
    Voidmonster, gooser and jemmo like this.
    Be careful how you treat people on your way up, you may meet them again on your way back down.

  12. The Following User Says Thank You to JimmyHAD For This Useful Post:

    Voidmonster (08-16-2014)

  13. #7
    Senior Member blabbermouth 10Pups's Avatar
    Join Date
    Nov 2012
    Location
    Across the street from Mickey Mouse in Calif.
    Posts
    5,320
    Thanked: 1184

    Default

    That came out perfect Zak. Looks like your shop is back in full swing after the flood resided :<0)
    Voidmonster likes this.
    Good judgment comes from experience, and experience....well that comes from poor judgment.

  14. The Following User Says Thank You to 10Pups For This Useful Post:

    Voidmonster (08-17-2014)

  15. #8
    Captain ARAD. Voidmonster's Avatar
    Join Date
    May 2011
    Location
    Pacifica, CA
    Posts
    2,474
    Thanked: 2226

    Default

    Quote Originally Posted by JimmyHAD View Post
    Thanks Zak. Aside from the as expected, beautiful job, I really appreciate your going through the steps you took in the restore. Not that I'd ever try such a job, but I'm sure many members here who are so inclined will learn from your post.
    One of these days, I'll have my act together enough to plan ahead and shoot video of the full restoration. I've got a couple of tricks I use (especially for fixing up old horn scales) that work really well for me. In general, I am very much a fan of repairing scales instead of replacing!

    'Course, these were in pretty good shape to begin with.
    -Zak Jarvis. Writer. Artist. Bon vivant.

  16. #9
    Captain ARAD. Voidmonster's Avatar
    Join Date
    May 2011
    Location
    Pacifica, CA
    Posts
    2,474
    Thanked: 2226

    Default

    Quote Originally Posted by 10Pups View Post
    That came out perfect Zak. Looks like your shop is back in full swing after the flood resided :<0)
    It's better'n ever, now!



    Cramped.

    A bit messy...

    But very, very functional!
    -Zak Jarvis. Writer. Artist. Bon vivant.

  17. #10
    Senior Member JSmith1983's Avatar
    Join Date
    Feb 2012
    Location
    Menominee,MI
    Posts
    1,624
    Thanked: 325

    Default

    You Lather Well And Ill Shave Well. I love it.
    Voidmonster likes this.

  18. The Following User Says Thank You to JSmith1983 For This Useful Post:

    Voidmonster (08-17-2014)

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •