Results 1 to 10 of 11
Thread: H. Boker Restore
-
01-24-2017, 01:53 AM #1
H. Boker Restore
The scales were trashed. And when I took them off they crumbled in my hands. A bit of rust but nothing really bad. A nick in the back edge of the heal. So I used some Black African wood I got from a member here and some silver pinning. Bone for the wedge. A lot of elbow grease as I don't have a buffer and this is the outcome. I still need to set the bevel as its not agreeing with me as far as the bevel but I'll get it. Hopefully.
I made a few mistakes with the scales but over all I'm happy. With the age of the razor, a few blemishes are keeping it looking like an old razor. That my excuse anyway.It's just Sharpening, right?
Jerry...
-
The Following 4 Users Say Thank You to Gasman For This Useful Post:
Dieseld (01-25-2017), Euclid440 (01-24-2017), ScoutHikerDad (01-24-2017), xiaotuzi (01-24-2017)
-
01-24-2017, 02:07 AM #2
After taking scales off. As you can see I didn't have a lot of work to do.
It's just Sharpening, right?
Jerry...
-
01-24-2017, 02:43 AM #3
Nice work, keep up the good work
I am very appreciative of all the knowledge and sharing each and everyone has provided me with. Look forward to future endeavors with many of you.
Gonzo
-
01-24-2017, 03:08 PM #4
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215Nice work.
It is not unusual to have to put in more work to set a bevel on a razor that has been sanded and or buffed.
It does have some aggressive spine wear, so will need at least, 2 layer of tape and possibly 3 to set the bevel, then drop back down to 2.
Take your time and ensure the bevel is fully set before moving on, or it will fight you all the way.
-
The Following User Says Thank You to Euclid440 For This Useful Post:
Steel (01-25-2017)
-
01-24-2017, 08:14 PM #5
I was going with two so maybe ill try three next time. Thanks for the hint.
It's just Sharpening, right?
Jerry...
-
01-24-2017, 11:12 PM #6
Beautiful job, Gasman! One thing that made all the difference with me on pinning after a few frustrating attempts was to start flush-cutting my pinstock a hair closer to the washer. After that, getting your domed "mushroom" with the jeweler's hammer becomes much easier. It made pinning MUCH easier on both ends, and a tighter, more secure pivot too! Looks great-love the black wood (ebony?)!
-
01-25-2017, 12:19 AM #7
Yeah, i left too much pin and my mushrooming took way too long and they are not as clean as they could be. I might do it over someday.
It's just Sharpening, right?
Jerry...
-
01-25-2017, 02:32 AM #8
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215If when pinning, you feel you have left the pin too long, file a bit off the top of the dome and keep pinning, hitting the edge.
You can also shape the pin, with a small needle file. Grind or sand one edge off smooth, on a grinder or belt sander, to make a safe edge that will not cut into the scale, or make a mask from an aluminum soda can, or piece of plastic from a milk jug, taped to the scale with a hole punched in the mask.
Shape the pin head, a magnifying visor and a strong task light will help you see your work much more clearly. Harbor Freight has a nice one for about $5, with 3 lenses.
Slowly, file off any unevenness in the pin or the crown, get the size and shape, of the dome the same for all of them.
If you pinning material is too hard, annealing, will soften it and make pinning much easier. Here again the magnifying visor, will help you see where your hammer hits are landing and their effects.
Finally, a 3-4-inch piece of bamboo chopstick, chucked in a drill press with a small divot on the end and a dab of Diamond Paste or Rubbing Compound, will grind the pins smooth and perfectly round. A dab of polish will make them gleam.
-
The Following 6 Users Say Thank You to Euclid440 For This Useful Post:
DoughBoy68 (01-26-2017), Gasman (01-25-2017), Mrchick (01-25-2017), nightcap (01-26-2017), ScoutHikerDad (01-25-2017), Steel (01-25-2017)
-
01-25-2017, 09:10 AM #9
Very good info to have. Thanks for sharing the details. I know this will help me to get a good looking pinning done. And the way to polish, thats a great touch. Thanks.
It's just Sharpening, right?
Jerry...
-
01-26-2017, 06:17 PM #10
Even though it may take some extra work to set the bevel the shave will be worth it as Bokers are extremely fine shavers. I still have a couple and love them. Enjoy!
"If You Knew Half of What I Forgot You Would Be An Idiot" - by DoughBoy68