Page 1 of 2 12 LastLast
Results 1 to 10 of 13
Like Tree4Likes

Thread: Robeson in black and red.

  1. #1
    Member theeditor's Avatar
    Join Date
    Apr 2011
    Location
    Lancaster, pa
    Posts
    44
    Thanked: 0

    Default Robeson in black and red.

    Simple black and red. Homemade micarta (envirotex). SS washers, nickel silver pin.

    Enjoy.
    Bruce
    Name:  IMG_20111025_062609.jpg
Views: 414
Size:  18.4 KBName:  IMG_20111210_155604.jpg
Views: 410
Size:  8.8 KBName:  IMG_20111210_155819.jpg
Views: 397
Size:  15.5 KBName:  IMG_20111210_155834.jpg
Views: 407
Size:  17.1 KB
    TURNMASTER, Dunc and IcemanOkC like this.

  2. #2
    Poor Fit
    Join Date
    May 2010
    Posts
    4,562
    Thanked: 1263

    Default

    Good lookin razor there. Nice work

  3. #3
    Member Str8Raz0r's Avatar
    Join Date
    Apr 2011
    Location
    Brisbane, Australia
    Posts
    1,434
    Thanked: 642

    Default

    Nice work on the micarta. The red wedge with the black scales looks good.

  4. #4
    Member theeditor's Avatar
    Join Date
    Apr 2011
    Location
    Lancaster, pa
    Posts
    44
    Thanked: 0

    Default

    Thanks much. It took a lot of batches to get the micarta right. I'm still not perfectly happy with it but much more so than I was.

    This has to be hands down the best shaving razor i've used yet. either that or I've found my honing streak. Hated to give this away.

    Thanks.

  5. #5
    Senior Member RayCover's Avatar
    Join Date
    Oct 2011
    Location
    Festus, MO
    Posts
    377
    Thanked: 113

    Default

    Nice Job. I like the shape of the scales and the double pins in the wedge end. Personally, I think I would have kept the hammered texture on the shank/tang. I think the contrast between the textures would have been fairly attractive. Still made a nice looking razor.

    Ray

  6. #6
    Member theeditor's Avatar
    Join Date
    Apr 2011
    Location
    Lancaster, pa
    Posts
    44
    Thanked: 0

    Default

    Quote Originally Posted by RayCover View Post
    Nice Job. I like the shape of the scales and the double pins in the wedge end. Personally, I think I would have kept the hammered texture on the shank/tang. I think the contrast between the textures would have been fairly attractive. Still made a nice looking razor.

    Ray
    I really wanted to. I just couldn't figure out how to effectively sand in the divots and it was pitted. I love the texture and plan to use that in the future..

  7. #7
    Senior Member RayCover's Avatar
    Join Date
    Oct 2011
    Location
    Festus, MO
    Posts
    377
    Thanked: 113

    Default

    To keep that texture you can strip the rust chemically. You can use naval jelly or bluing stripper to remove the rust. I would leave the pits as part of the texture. Then dip it in baking soda solution to neutralize the acids. Then rinse it clean.

    At that point the rust would be gone and you would be back to a neutral steel surface. It would probably be a good idea to coat it with WD-40 and let it set overnight to make sure and pull any moisture away from the surface of the steel. Should be ready to go at that point.

    Sometimes the acids in the rust/bluing strippers can turn the rust black as it neutralizes it. If that happens you can dip it in paint prep acid to take it back to white. If you like the darker antiqued color you can dip it in ferric chloride and that will leave a darker finish. Then you an burnish or lightly sand off he surface and get an antiqued sort of look to the whole area and camouflage in the pits so they can't be noticed.

    Ray
    rangerdvs likes this.

  8. #8
    Member theeditor's Avatar
    Join Date
    Apr 2011
    Location
    Lancaster, pa
    Posts
    44
    Thanked: 0

    Default

    Quote Originally Posted by RayCover View Post
    To keep that texture you can strip the rust chemically. You can use naval jelly or bluing stripper to remove the rust. I would leave the pits as part of the texture. Then dip it in baking soda solution to neutralize the acids. Then rinse it clean.

    At that point the rust would be gone and you would be back to a neutral steel surface. It would probably be a good idea to coat it with WD-40 and let it set overnight to make sure and pull any moisture away from the surface of the steel. Should be ready to go at that point.

    Sometimes the acids in the rust/bluing strippers can turn the rust black as it neutralizes it. If that happens you can dip it in paint prep acid to take it back to white. If you like the darker antiqued color you can dip it in ferric chloride and that will leave a darker finish. Then you an burnish or lightly sand off he surface and get an antiqued sort of look to the whole area and camouflage in the pits so they can't be noticed.

    Ray
    Thanks. I have naval jelly but wasnt sure how to get rid of the black that it leaves. Will the naval jelly harm an etching?

  9. #9
    Senior Member RayCover's Avatar
    Join Date
    Oct 2011
    Location
    Festus, MO
    Posts
    377
    Thanked: 113

    Default

    IF you talking about logos and names etched int eh shank, as long as you don't leave it on any longer than needed to remove the rust you should not see any appreciable deterioration of the original etch. That is, as long as the original etching is deep enough to be more than just changing the color on the surface.

    Ray

  10. #10
    Senior Member medicevans's Avatar
    Join Date
    Jul 2011
    Posts
    768
    Thanked: 99

    Default

    Tell us more about the micarta. My envirotex hasn't come out nearly as nice yet.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •