Results 1 to 7 of 7
Like Tree5Likes
  • 3 Post By BobH
  • 1 Post By rolodave
  • 1 Post By henryconchile

Thread: Lather problems

  1. #1
    Senior Member
    Join Date
    Apr 2013
    Posts
    117
    Thanked: 0

    Default Lather problems

    Hello. I can't create any decent lather. I have a whipped dog badger silvertip 22 mm knot. I tried soaking the brush for 5 minutes before shaving. I also tried to wet it really well. I have acceptable amount of lather for the first pass but not for my second. I used Proraso green soap but I found it difficult to create lather. Now I use Palmolice cream. It's a little better but nowhere near as it should be.

  2. #2
    Senior Member dinnermint's Avatar
    Join Date
    Jan 2012
    Location
    Waukesha, Wisconsin
    Posts
    1,943
    Thanked: 390

    Default

    What are your steps in creating a lather and how much soap do you use?

    This might help too... http://straightrazorpalace.com/begin...ng-videos.html

  3. #3
    Senior Member blabbermouth
    Join Date
    Mar 2012
    Location
    Thunder Bay, Ontario, Canada
    Posts
    17,295
    Thanked: 3225

    Default

    Here is another vid that helped me out .

    If you only have enough for one pass then you did not load enough soap in the brush. Load lots of soap then slowly add water till you have the right mix of soap to water. Personally I use a version of the "dry" meathod.

    Bob
    rolodave, JTmke and xiaotuzi like this.
    Life is a terminal illness in the end

  4. #4
    Senior Member JTmke's Avatar
    Join Date
    May 2014
    Location
    Milwaukee
    Posts
    1,367
    Thanked: 176

    Default

    Load more. If your loading for 15 seconds, try 45 seconds. You'll figure out lather better in the beginning by having too much. Just go at the cream or soap until the brush looks full at the tips. Then trickle water in as you bowl/face lather. The soap or cream will start to expand as you add the water and swirl the brush. Keep adding tiny amounts of water until you reach your desired consistency. Not runny or full of big bubbles.
    "The best way to have a good idea is to have a lot of ideas." -Linus Pauling

  5. #5
    Moderator rolodave's Avatar
    Join Date
    Aug 2011
    Location
    Racine, WI USA
    Posts
    7,741
    Thanked: 1936
    Blog Entries
    1

    Default

    The lather left over can be gently squeezed back into the bowl or cup.

    The key word is "gently". Don't break the bristle or hair.
    xiaotuzi likes this.
    If you don't care where you are, you are not lost.

  6. #6
    Make ready the heat. henryconchile's Avatar
    Join Date
    Aug 2012
    Location
    Metro Boston, MA
    Posts
    404
    Thanked: 74

    Default

    You shouldn't need to soak a badger brush for 5 min. You can get good lather for a 1 min soak. I've gotten great lather from just soaking my Vulfix brush for 30 seconds.

    How much water do you shake off the brush? If you remove too much water from the brush, then you end up with a bad, thick lather; however, you can always add drips of water to your mug, while lathering, to improve your lather under this condition. If you remove too little water from the brush, then you end up with a runny lather. Different soaps/creams require different amounts of water. You'll have to experiment.

    How long are you swirling the brush to create your lather. I'd recommend lathering for at least 1 min. Try 2 min, just to check out your results. Soaps require more lather time than creams.
    rolodave likes this.
    You can take the boy out of NY, but you can't take NY out of the boy.

  7. #7
    Junior Member
    Join Date
    Aug 2016
    Location
    Canada
    Posts
    4
    Thanked: 0

    Default

    Thank you for the valuable information.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •