Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24
  1. #11
    Knife & Razor Maker Joe Chandler's Avatar
    Join Date
    Feb 2006
    Location
    Louisiana
    Posts
    1,849
    Thanked: 50

    Default

    Try the Mil-Comm TW2500. Way better than the Ballistol, IMO, and is also non-toxic, and doesn't even smell bad. Harder to get, though. I use it and the TW25B (paste) on damn near everything, from knives to guns to door hinges.

  2. #12
    Member AFDavis11's Avatar
    Join Date
    May 2005
    Location
    Virginia
    Posts
    5,726
    Thanked: 1486

    Default

    I recommend rinsing the blade in hot water, not cold. You guys sure know your chemicals. :-)

  3. #13
    Senior Member EdinLA44's Avatar
    Join Date
    Jan 2006
    Location
    Los Angeles
    Posts
    608
    Thanked: 2

    Default

    Quote Originally Posted by Joe Chandler
    Try the Mil-Comm TW2500. Way better than the Ballistol, IMO, and is also non-toxic, and doesn't even smell bad. Harder to get, though. I use it and the TW25B (paste) on damn near everything, from knives to guns to door hinges.
    Joe,

    Thanks for the tip. I just ordered a 16.9 oz spray can of the TW25B (their site didn't have anything with TW2500 on it). Hopefully this is the right product. The TW25B product I got is a spray, so it should be fine. They did have an MC2500, but it was also a spray. Not sure what the difference is though. Maybe I'll go back and order that too.

    Ed
    Last edited by EdinLA44; 03-20-2006 at 12:14 AM.

  4. #14
    The Hurdy Gurdy Man thebigspendur's Avatar
    Join Date
    May 2005
    Location
    New Mexico
    Posts
    33,039
    Thanked: 5020
    Blog Entries
    4

    Default

    I have noticed that my razors accumulate dark spots also but they are more like dark smudges maybe an eighth inch in size. I don't know where they come from, I always rinse off the razor with hot water and wipe it down good when I'm done then let it air dry then coat with sterol.

    I've more or less gotten used to them. They don't seem to have any lasting effects and any metal cleaner takes them right off.
    No matter how many men you kill you can't kill your successor-Emperor Nero

  5. #15
    Robert Williams Custom Razors PapaBull's Avatar
    Join Date
    May 2005
    Location
    East Liverpool, Ohio
    Posts
    971
    Thanked: 324

    Default

    To keep blades bright, I've had good results rinsing with the hottest water I could run the razor under and then drying/polishing with a few layers of toilet paper. It's very absorbent and paper polishes. The razor is bright and completely dry after that.

  6. #16
    Senior Member ForestryProf's Avatar
    Join Date
    Oct 2005
    Location
    Auburn, AL
    Posts
    839
    Thanked: 8

    Default

    I'm with Robert,
    I finish off by rinsing with the last of the boiled water that is left in my shaving thermos; I pour it over the razor and into my rinsed shaving mug for a final rinse of my brush. I then wipe down the razor either with toilet paper or a dry section of my shaving towel. Because the razor has been heated by the still very hot water, it dries completely. Even so, I leave it open on a shelf during the day while at work. No spots so far...
    Ed

  7. #17
    Senior Member superfly's Avatar
    Join Date
    May 2005
    Location
    Toronto, ON
    Posts
    1,950
    Thanked: 16

    Default

    Watch out with hot water... It is fast way to warp and damage the scales. Lately, I am soap-washing the razors after shaving, wipe dry with towel, and blow hard between the scales and also in the pivot. After that is stroping, and the razor is left closed on top of the box to dry out whatever moisture has left. I dont oil at all these couple of months, and the razors are just fine...

    Nenad

  8. #18
    Senior Member ForestryProf's Avatar
    Join Date
    Oct 2005
    Location
    Auburn, AL
    Posts
    839
    Thanked: 8

    Default

    Nenad is spot on. I should have been clear...keep the water away from the scales. I pour the boiled water down the razor from only about half way up the tang.
    Ed

  9. #19
    Junior Member
    Join Date
    Mar 2006
    Posts
    4
    Thanked: 0

    Default

    In the Civil War, the combatants washed their revolvers with scalding hot water. (black powder is very corosive, and cleans well in water) This process heated the steel, and prevented rusting. I apply this logic to my razors, and virtually scald them before wiping with my shave towell. When I put them away, they never rust. I will add that my climate is also very dry.

  10. #20
    Knife & Razor Maker Joe Chandler's Avatar
    Join Date
    Feb 2006
    Location
    Louisiana
    Posts
    1,849
    Thanked: 50

    Default

    I'll agree with Virgil. I just run mine under scalding hot water, then wipe off. No rust yet, and I live in Louisiana (i.e., jungle weather) I will occasionally put some Tuf-Glide or TW2500 on them.

Page 2 of 3 FirstFirst 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •