Results 1 to 10 of 25
Thread: DMT Coarse 325 8"
Hybrid View
-
05-20-2014, 03:36 AM #1
Lynn has a youtube video about lapping. He recommends lapping under running water to keep them from sticking. http://youtu.be/
I did my Naniwa 12k today and it worked well. Not sure how long the DMT will last, but i'd assume a lomg time...they're very hard.Last edited by Haroldg48; 05-20-2014 at 04:28 AM.
Just call me Harold
---------------------------
A bad day at the beach is better than a good day at work!
-
The Following User Says Thank You to Haroldg48 For This Useful Post:
JTmke (05-22-2014)
-
05-20-2014, 04:44 AM #2
- Join Date
- Apr 2014
- Location
- Minnesota
- Posts
- 240
Thanked: 18I'm just about to pull the trigger on the DMT 325. Just received a naniwa 12k today got a C12k last week and a swaty enroute. So will be doing some lapping sooner rather than later !
-
05-20-2014, 04:56 AM #3
- Join Date
- Apr 2014
- Location
- Minnesota
- Posts
- 240
Thanked: 18OK I just ordered myself the DMT from SRD!!!!! Can't wait to get it.
-
05-20-2014, 12:05 PM #4
When you get it, here are a few helpful tips that I got from members here:
1) Break it in, by rubbing the shaft of a screwdriver or older knife up and down it some in order to remove any "misplaced" pieces of diamond that could otherwise put a scratch in your hone.
2) Keep it wet when lapping by doing it under running water.
3) Don't let the "slurry" build up; rinse it off both the hone and the DMT regularly during the lapping.
4) Use the pencil grid technique on your hone to make sure that you get it really flat.
5) Clean it after use with Comet or Ajax and a nylon scrub brush.
Many of those instructions come with the DMT, but I know how "we" are with reading instructionsJust call me Harold
---------------------------
A bad day at the beach is better than a good day at work!
-
The Following 3 Users Say Thank You to Haroldg48 For This Useful Post:
Avenolpey (05-20-2014), JTmke (05-22-2014), nodakjohns (05-22-2014)
-
05-20-2014, 10:47 PM #5
- Join Date
- Dec 2012
- Location
- Long Island NY
- Posts
- 1,378
Thanked: 177DMT will not hold up to vigorous lapping on very hard naturals. Use the 60 grit wet/dry for that. Synths should be no problem at all.
-
The Following User Says Thank You to bill3152 For This Useful Post:
Avenolpey (05-20-2014)
-
05-20-2014, 11:01 PM #6
- Join Date
- Feb 2013
- Location
- Haida Gwaii, British Columbia, Canada
- Posts
- 14,406
Thanked: 4824my plates have held up to a lot of use. DMT has a video and recommends that it is either used under water, as in in a pan of water or under running water in a sink. I have put mine through a lot and they keep going.
It's not what you know, it's who you take fishing!
-
The Following User Says Thank You to RezDog For This Useful Post:
Avenolpey (05-20-2014)
-
05-20-2014, 11:12 PM #7
I've been using my DMT 325 for almost six years, and mostly on naturals, and some very hard ones. It still cuts quite well, although it's not as fast as when new. But, sometimes we seek a well broken-in DMT also..
Don't worry ... It will last you a good long time, on synth or naturals.
-
The Following User Says Thank You to Druid For This Useful Post:
Avenolpey (05-20-2014)